708059

Spektrum DX8 Manual

17
Zoom out
Zoom in
Previous page
1/42
Next page
17


Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Trim Setup then press to access the function.
The following screen appears:
Highlight the desired Trim value then press the roller to access. Rotate the roller to
change to the desired trim value. Press to accept. Repeat to adjust all trim steps.

Rotate the roller to highlight Trim Type and press to access.
Select F-Mode (each flight mode has its own trims) or Common (trim are always
common regardless of flight mode).
Common Trim - When common trim is selected, trim values are common in all
flight modes.
F-Mode Trim - When F-Mode is selected, each flight mode including hold has its
own trims that are automatically active when that flight mode is selected.

Model Reset is typically used to clear the programming for a model you will no
longer be flying. Model Reset resets the programming for the selected model
to factory defaults. No other model memories will be affected. When a model’s
memory is reset all programming for that model is permanently deleted and
cannot be recovered.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Model Reset then press to access the function.
The following screen appears:
Verify that the model displayed on this screen is the model you wish to reset. If
not then see page 14 Model Select to access the desired model. Rotate the roller
to highlight Reset and then press to access the Confirm Reset screen.
Highlight YES If you’re sure you want to reset this model to factory default
settings, press the roller. The screen will return to the main screen.

The Model Copy function copies the currently selected model’s programming of
another model memory. Thirty model memories are available. Some of the more
common uses of the Model Copy function include:
•Movingtheorderofmodelsaroundinmodelmemorysotheycanbeorganized
by category, type, etc. Note: You will need to re-bind after moving models.
•Experimentingwiththeprogrammingforanaircraftwhilepreservingacopy
of the original setup. Note: If you want to use the model copy function to try
two slightly different setups with the same model you will need to rebind the
receiver each time you switch between model memories.
•Copyingtheprogrammingforanexistingmodelovertoanewmodelthat
is similar. Many pilots find this to be a good way to provide more accurate
baseline programming for the new model. For example Vibe 50 w/120CCPM
mixing, gyro and governor programming provides a good base programming
for any other nitro powered 120CCPM mixing helicopter. An Extra 300 with
dual aileron and elevator servos that is properly programmed with dual flap and
dual elevator mixing in Wing Type provides good foundational programming
for another aerobatic airplane with the same basic control system.
Important: The model memory you are copying to will be over-written by the
copied programming, permanently deleting any programming that may already exist.

Press and hold the roller while turning on the transmitter. When System Setup
appears on the screen, release the roller. The DX8 is now in System Setup Mode.
Rotate the roller to highlight Model Copy then press.
The following screen appears:
EN
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX8 in the language / languages: English as an attachment in your email.

The manual is 5,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX8

Spektrum DX8 Quick start guide - English - 100 pages

Spektrum DX8 User Manual - German - 42 pages

Spektrum DX8 User Manual - French - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info