726853

Spektrum DX18 - SPM18000 Manual

26
Zoom out
Zoom in
Previous page
1/42
Next page
26 SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL
EN
Sequencer
The Sequencer menu option provides this-then-that mixing with
a time delay. Five different sequences (S1 through S5) are avail-
able to control 2 functions each (A and B), in 2 timing directions
(forward or reverse). Sequences appear throughout function
screens as assignable switches.
CAUTION: Always review the action of a sequence on
the Monitor or X-Plus Monitor screen BEFORE operating
the model to ensure controls act as desired. Failure to do so
could cause a crash, resulting in property damage and or injury.
You can program multiple functions to sequentially activate
in response to an assigned switch. For example, an assigned
Gear switch can open gear doors, lower the gear, then close the
doors. In reverse, gear doors open, the gear retracts and the
gear doors close.
You can assign each Sequencer function to a switch in most
Function screens such as Flight Mode, Dual Rate, Mixing,
Throttle Curve, Pitch Curve, etc.
You can assign several functions to a sequence to decrease
the number of controls you need to touch during complex fl ight
transitions, for example, applying your assigned dual rates and
exponential when the landing gear deploys and the fl ight mode
changes.
If you select an S-Number-A sequence, for example, S3A, the
sequence operates as a timed 5-position switch. An S-Number-
B sequence operates as a timed 3-position switch. The 5
positions correspond to the sequencer values shown on the
time delay graph in the second Sequencer screen. In a function
screen, highlight each point (0-4) and select the switch position
desired for a function to be active.
When S1B (or another sequence-number-B) is selected as
a switch in a function, the sequence will operate as a timed
3-position switch. The 3 positions act as ‘kick points’ of the
movement at fi xed percentages (equal thirds) of the sequencer
output. In a function screen, highlight each point (0-2) and select
the switch position desired for a function to be active.
Sequencer Set Up
1. In the fi rst Sequencer screen, select 1 of the 5 available
sequences.
2. In the second Sequencer screen, assign a switch to the
sequence. We recommend using a 2-position switch.
Tip: If you need to use a 3-position switch, you must assign
one direction to two adjacent switch positions, for example,
0 and 1. Assign the opposite direction to the third switch
position.
3. Assign the timing for the Forward and Reverse directions as
desired. There is no delay when you use the Nor option. You
may also select a delay time between 0 and 30 seconds.
4. Assign names for each sequencer function, as desired.
5. Select either Step (S) or Proportional (P) for the Sequencer
output.Step: The sequence only changes at kick points.
Otherwise, there is a delay in the sequence until it reaches
the next kick point.
Proportional: The sequence movement is proportional
between kick points. The sequence maintains rate and
direction until it reaches the next kick point.
6. Adjust the Sequencer motion percentages in the third screen.
For example, you may move points 1, 2 and 3 closer to the
beginning of the sequence so the motion occurs earlier. This
results in a delay between point 3 and point 4 at the end of the
sequence.
Testing the Sequence
The Sequencer function determines the response for channels
included in the sequence.
Refer to the Monitor screen to see how respective channels
interact in the Sequencer.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX18 - SPM18000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX18 - SPM18000 in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX18 - SPM18000

Spektrum DX18 - SPM18000 User Manual - German - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info