726853

Spektrum DX18 - SPM18000 Manual

25
Zoom out
Zoom in
Previous page
1/42
Next page
25SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL
EN
Mixing
Mixing allows control input for a channel to affect more than one
channel at a time. Mixing functions support:
• Mixing a channel to another channel.
• Mixing a channel to itself.
• Assigning offset to a channel
• Linking primary to secondary trim.
These mixes are available for each model memory:
16 programmable mixes
Select a channel for master and slave. Inputs for the mas-
ter channel control both the master and slave channels. For
example Elevator to Flap makes elevator the master channel and
fl ap the slave channel.
Offset
Change the offset value to move the effective center position
of the slave channel. Positive or negative value determines the
direction of the offset. Offset is not available for curve mixes.
Trim
If the master channel trim should also adjust the slave channel,
set Trim to Act. A channel monitor on the left side of the screen
shows how channels respond to input. To view a switch-as-
signed mix on the monitor, the mix switch must be in the active
position.
Assigning a Mix to a Switch
If you wish to assign a mix to a switch position:
1. Scroll to Switch and press the scroll wheel.
2. Scroll left or right to the switch you wish to use and press
the scroll wheel to save the selection.
3. Scroll to the switch position where you want the mix to be
active.
The mix is Active when the box is fi lled and Inactive when the
box is open. You can assign a mix to be active in multiple switch
positions (0,1 or 2).
CAUTION: Always do a Control Test of your model
after changing mixes.
Combo Mixing
Combination Mixing is available to create OR mixing where you
can assign 2 conditions and the mix activates if either condition
occurs. You can also create AND mixing where 2 conditions
must occur to activate the mix.
To program Combination Mixing:
1. Activate a mix.
2. Select Combo Sw. in the Switch Selection. The Combo
screen appears.
3. Select the desired switch and active switch position for
Switch 1.The mix is Active when the switch position box is
fi lled.
4. Select the Relation (AND, OR)
5. Select the desired switch and active switch position for
Switch 2.The mix is Active when the switch position box is
fi lled.
6. Press the BACK button to save the Combination Mix.
The Master (left side) names are inputs. For example, “Aileron”
refers to the Aileron Stick. The Slave (right side) name is the
name of the channel receiving the mix command when the
Master channel moves.
Back Mixing
Back Mixing applies a mix to all related servos in a wing or tail
type. For example, if you select 2 AIL, 2FLAP in the Aircraft Type
screen, a mix to one aileron channel affects both aileron servos.
The mix response, however, depends on the aileron channel
included in the mix.
A Back Mix also enables you to use fewer mixes to achieve the
desired response, for example adding roll to a split elevator.
• Cyclic to Throttle (HELI)
• Swashplate (HELI)
• Elevator to Flap (ACRO)
• Aileron to Rudder (ACRO)
• Rudder to Aileron/Elevator
(ACRO).
• Aileron>Rudder (SAIL)
• Aileron>Flap (SAIL)
• Elevator>Flap (SAIL)
• Flap>Elevator (SAIL)
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX18 - SPM18000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX18 - SPM18000 in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX18 - SPM18000

Spektrum DX18 - SPM18000 User Manual - German - 39 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info