733462
26
Zoom out
Zoom in
Previous page
1/60
Next page
21
(1) If your bike has cam action front wheel retention, move the cam lever so
that it curves away from the wheel (fig. 8b). This is the OPEN position. If your
bike has through bolt or bolt-on front wheel retention, go to the next step.
(2) With the steering fork facing forward, insert the wheel between the fork
blades so that the axle seats firmly at the top of the fork dropouts. The cam
lever, if there is one, should be on rider’s left side of the bicycle (fig. 8a & b). If
your bike has a clip-on type secondary retention device, engage it.
(3) If you have a traditional cam action mechanism: holding the cam lever in
the ADJUST position with your right hand, tighten the tension adjusting nut with
your left hand until it is finger tight against the fork dropout (fig. 8a). If you have
a cam-and-cup system: the nut and cup (fig. 8b) will have snapped into the
recessed area of the fork dropouts and no adjustment should be required.
(4) While pushing the wheel firmly to the top of the slots in the fork dropouts,
and at the same time centering the wheel rim in the fork:
(a) With a cam action system, move the cam lever upwards and swing it
into the CLOSED position (fig. 8a & b). The lever should now be parallel to the
fork blade and curved toward the wheel. To apply enough clamping force, you
should have to wrap your fingers around the fork blade for leverage, and the
lever should leave a clear imprint in the palm of your hand.
(b) With a through-bolt or bolt-on system, tighten the fasteners to the torque
specifications in Appendix D or the hub manufacturer’s instructions.
NOTE: If, on a traditional cam action system, the lever cannot be pushed all
the way to a position parallel to the fork blade, return the lever to the OPEN
position. Then turn the tension adjusting nut counterclockwise one-quarter
turn and try tightening the lever again.
WARNING: Securely clamping the wheel with a cam action
retention device takes considerable force. If you can fully close the
cam lever without wrapping your fingers around the fork blade for
leverage, the lever does not leave a clear imprint in the palm of
your hand, and the serrations on the wheel fastener do not emboss
the surfaces of the dropouts, the tension is insufficient. Open the
lever; turn the tension adjusting nut clockwise a quarter turn; then
try again. See also the first WARNING in this Section, p. 18.
(5) If you disengaged the brake quick-release mechanism in 3. a. (1) above,
re-engage it to restore correct brake pad-to-rim clearance.
(6) Spin the wheel to make sure that it is centered in the frame and clears the
brake pads; then squeeze the brake lever and make sure that the brakes are
operating correctly.
c. Removing a disk brake or rim brake Rear Wheel
(1) If you have a multi-speed bike with a derailleur gear system: shift the rear
derailleur to high gear (the smallest, outermost rear sprocket).
If you have an internal gear rear hub, consult your dealer or the hub
manufacturer’s instructions before attempting to remove the rear wheel.
If you have a single-speed bike with rim or disk brake, go to step (4) below.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Specialized 2007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Specialized 2007 in the language / languages: English as an attachment in your email.

The manual is 3,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Specialized 2007

Specialized 2007 User Manual - German - 60 pages

Specialized 2007 User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info