611474
17
Zoom out
Zoom in
Previous page
1/60
Next page
15Soundcraft MFXi MPMi User Guide Issue 1210
12 PEAK LED This is used to indicate that the signal is close to distorting (clipping) on a specic
channel.
13 SP LED The SP LED glows when a signal is present. The feed point for the LED is post-insert,
pre-EQ.
14 INPUT CHANNEL FADER This is used to control the level fed to the Mix Bus and post-fade sends.
15 MIX OUTPUTS (XLR) Connect these to your analogue recording device, or to your amplication &
MONO OUT (¼” Jack) system.
16 SUB-GROUP OUTPUTS These outputs can be connected to a separate amplier system or to an external
(¼” Jack) processor.
17 SUB-GROUP ROUTING The sub-group mix can be routed to the main mix, in mono or stereo.
18 MASTER FADERS These faders control the overall level of the mix and sub-group outputs.
19 MAIN METERS These show the level of the mix outputs. When the master SOLO LED is lit, the meters
show the level of the selected AFL/PFL signal.
20 MONITOR OUTPUTS These are used to feed your monitoring system. This can be directly connected to
(¼” Jack) powered monitors, or indirectly via an amplier to standard monitors.
21 MONITOR CONTROL This controls the level of the signal sent to your monitoring system.
22 MONITOR SELECT SWITCH This switch selects the signal source to be monitored. Note that the 2-TK input can
be monitored also, see item 30 below.
23 PHONES CONTROL This controls the level of the signal sent to the headphones jack socket.
24 HEADPHONES (¼” Jack) Plug your headphones into this socket. Recommended headphones impedance is
32 ohms or greater.
25 AUX 1, 2 & 3 OUTPUTS These outputs can be used to send the channel signal to an artist’s monitors
(¼” Jacks) (headphones/in-ear/stage monitors), external FX or secondary PA/monitor system.
26 AUX CONTROLS The rotary controls set the output levels of the three Aux Outputs. The After
& AFL SWITCHES Fade Listen (AFL) switches route their respective aux output signal to the monitor/
headphones outputs.
27 AUX 2 POST/PRE SWITCH This switch globally changes the AUX 2 feed on all the input modules to be either
post-fade or pre-fade.
28 STEREO INPUTS (¼” Jack) These two pairs of inputs can be used to connect line level stereo inputs from key-
boards, sound modules, samplers, computer based audio cards etc. These inputs
pass through a stereo channel strip, with EQ, Auxes and a Balance control. Mono
sources may be used by plugging into the left jack only.
29 2-TRACK IN (RCA Phono) You can connect the playback from your recording device here.
30 2-TRACK OUT Use these to control the 2 Track signal. The Monitor switch sends the signal to the
monitor outputs and phones, whilst the TO MIX switch sends it to the main mix.
31 Record Outputs (RCA Phono) You can connect these to the inputs of your recording device.
32 PHANTOM POWER Press this to globally switch the phantom power (48V) on for condenser microphones.
WARNING: Do Not apply Phantom Power before connecting a micro-
phone.
Your MPMi console is equipped with a Kensington® Security slot on the rear panel for use with compatible PC/Laptop security cables.
For more information about the Kensington range of security devices please visit http://us.kensington.com
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MPMi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MPMi in the language / languages: English as an attachment in your email.

The manual is 2,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Soundcraft MPMi

Soundcraft MPMi User Manual - German - 35 pages

Soundcraft MPMi User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info