611455

Soundcraft MFX12 Manual

17
Zoom out
Zoom in
Previous page
1/48
Next page
17
POST-FADE), but for Foldback or Monitor feeds it is important for the send to be independent of the
fader (this is called PRE-FADE).
AUX SENDS 1 and 2 are both globally switchable between pre and post-fade (see master section
on page 20).
8 FX SEND
This control sets the level of the post-fade signal being sent to the FX bus; from there it is routed to
the FX processor. The FX Send is always post-fader.
9 PAN
This control sets the amount of the channel signal feeding the Left and Right MIX buses, allowing
you to move the source smoothly across the stereo image. When the control is turned fully left or
right you are able to route the signal at unity gain to either left or right outputs individually.
10 MUTE
All outputs from the channel except inserts are on when the MUTE switch is released and muted
when the switch is down, allowing levels to be pre-set before the signal is required. The MUTE
switch’s inbuilt LED glows when the channel is muted.
11 INPUT CHANNEL FADER
The 60mm FADER, with a custom-designed law to give even smoother control of the overall signal
level in the channel strip, allows precise balancing of the various source signals being mixed to the
Master Section. You get most control when the input GAIN is set up correctly, giving full travel on
the fader. See the “Initial Setup” section on page 33 for help in setting a suitable signal level.
12 PFL
When the latching PFL switch is pressed, the pre-fade pre-mute signal is fed to the headphones,
control room output and meters, where it replaces the MIX. The AFL/PFL ACTIVE LED on the Master
section illuminates to warn that a PFL is active. This is a useful way of listening to any required
input signal without interrupting the main mix, for making adjustments or tracing problems. When
PFL is pressed anywhere on the console, the Control Room outputs automatically switch from
monitoring the Mix Outputs.
13 PEAK LED
This LED will light when the signal level approaches clipping at any of the three monitored points:
PRE-EQ, POST-EQ and POST-FADE.
14 SIGNAL PRESENT (SP) LED
The SP LED glows when a signal is present. The feed point for the LED is post-EQ, pre-mute.
15 MIX/SUB
When this switch is up, the channel’s post-pan-pot signal is routed to the Mix (left and right) buses.
When the switch is depressed, the post-pan-pot signal is routed to the Sub-group (left and right)
buses.
It is sometimes useful to route several inputs to the sub-group buses, e.g. all the mics for a drum
kit, or all the vocal mics for a choir. These signals can then be fed to the main mix at the master
section. By doing this the levels of all of the grouped inputs can be changed together by using the
group faders instead of having to adjust all of the individual input faders, although, of course, the
individual channel faders will have to be adjusted to start with.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MFX12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MFX12 in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info