611455

Soundcraft MFX12 Manual

46
Zoom out
Zoom in
Previous page
1/48
Next page
46
GLOSSARY
AFL After-fade listen: a function that allows the operator to monitor the post-fade signal in
a channel independently of the main mix.
Auxiliary send An output from the console comprising a mix of signals from channels derived inde-
pendently of the main stereo mix.
Balance The relative levels of the left and right channels of a stereo signal.
Balanced A method of audio connection which ‘balances’ the wanted signal between two wires,
these wires also have a screen which carries no signal. Any interference is picked up
equally by the two wires, which results in cancellation of the unwanted signal. In this
guide, the term can refer to various circuit architectures. Connection details are given
in relevant sections.
Clipping The onset of severe distortion in the signal path, usually caused by the peak signal
voltage being limited by the circuit’s power supply voltage.
DAT Digital Audio Tape, a cassette-based digital recording format.
dB (decibel) A ratio of two voltages or signal levels, expressed by the equation dB=20Log10 (V1/
V2). Adding the suffix ‘u’ denotes the ratio is relative to 0.775V RMS.
DI(direct injection)/DI Box The practice of connecting an electric musical instrument directly to the
input of the mixing console, rather than to an amplifier and loudspeaker which is
covered by a microphone feeding the console.
Equaliser A device that allows the boosting or cutting of selected bands of frequencies in the
signal path.
Fader A linear control providing level adjustment.
Feedback The `howling’ sound caused by bringing a microphone too close to a loudspeaker
driven from its amplified signal.
Foldback A feed sent back to the artistes via loudspeakers or headphones to enable them to
monitor the sounds they are producing.
Frequency response The variation in gain of a device with frequency.
Gain The amount of amplication in level of the signal.
Headroom The available signal range above the nominal level before clipping occurs.
Impedance balancing A technique used on unbalanced outputs to minimise the effect of hum and interfer-
ence when connecting to external balanced inputs.
Insert A break point in the signal path to allow the connection of external devices, for in-
stance signal processors or other mixers at line level signals. Nominal levels can be
anywhere between 0dBu to +6dBu, usually coming from a low impedance source.
Pan (pot) Abbreviation of ‘panorama’: controls the levels sent to left and right outputs.
Peaking The point at which a signal rises to its maximum instantaneous level, before falling
back down again. It can also describe an equaliser response curve affecting only a
band of frequencies, (like on a graphic equaliser), “peaking” at the centre of that
band.
Peak LED A visual indication of the signal peaking just before the onset of clipping, which will
distort the signal.
PFL Pre-fade listen: a function that allows the operator to monitor the pre-fade signal in a
channel independently of the main mix.
Phase A term used to describe the relationship of two audio signals. In-phase signals rein-
force each other, out-of-phase signals result in cancellation. Phase is a measurement
of relative displacement between two waves of identical frequency.
Polarity A term used to describe the orientation of the positive and negative poles of an audio
connection. Normally connections are made with positive to positive, negative to
negative. If this is reversed, the result will be out-of-phase signals (see ‘phase’ above).
Post-fade The point in the signal path after a fader and therefore affected by the fader position.
… 46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft MFX12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft MFX12 in the language / languages: English as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info