611452
23
Zoom out
Zoom in
Previous page
1/60
Next page
21
Soundcraft EFX/EPM User Guide Issue 1210
STEREO INPUT CHANNELS (EFX shown)
1 INPUTS STEREO 1/2
These inputs accept 3-pole A gauge (TRS) jacks. Use these inputs for
sources such as keyboards, drum machines, synths, tape machines or
processing units. The inputs are BALANCED for low noise and top quality
from professional equipment, but you can use UNBALANCED sources by
wiring up the jacks as shown in the “Wiring it Up” section earlier in this
manual, although you should then keep cable lengths as short as possible.
Mono sources may be used by plugging into the left jack only.
2 GAIN
The GAIN control sets the level of the channel signal.
3 EQUALISER
HF EQ
Turn to the right to boost high (treble) frequencies, adding crispness to
percussion from drum machines, synths and electronic instruments. Turn
to the left to cut these frequencies, reducing hiss or excessive brilliance.
Set the knob in the centre-detented position when not required. The
control has a shelving response giving 15dB of boost or cut at 12kHz.
MF EQ
Turn to the right to boost mid frequencies, turn to the left to cut these
frequencies. The centre frquency of the MID EQ is 720Hz
LF EQ
Turn to the right to boost low (bass) frequencies, adding extra punch to
synths, guitars and drums. Turn to the left to reduce hum, boominess or
improve a mushy sound. Set the knob to the centre-detented position
when not required. The control has a shelving response giving 15dB of
boost or cut at 80Hz.
4 AUX 1 SEND
This is used to set up a separate mix for FOLDBACK or recording, and the
combination of each Aux Send is mixed to the Aux1 Output. For recording
it is useful for the signal to fade up and down with the fader (this is called
POST-FADE), but for Foldback or Monitor feeds it is important for the send
to be independent of the fader (this is called PRE-FADE).
AUX 1 SEND is globally switchable between pre and post-fade (see
master section on page 24/25). The send pot is fed with a mono sum
of the L & R signals.
5 FX SEND (EFX only)
This control sets the level of the post-fade signal being sent to the FX
bus; from there it is routed to the FX processor.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft EPM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft EPM in the language / languages: English as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info