611452

Soundcraft EPM Manual

21
Zoom out
Zoom in
Previous page
1/60
Next page
19
Soundcraft EFX/EPM User Guide Issue 1210
Note that some sound equipment, particularly that intended for domestic
use, operates at a lower level (-10dBV) than professional equipment and
will therefore need a higher gain setting to give the same output level.
See “Initial Setup” on page 31 to learn how to set GAIN correctly.
5 Equaliser
The Equaliser (EQ) allows ne manipulation of the sound, particularly
to improve the sound in live PA applications where the original signal
is often far from ideal and where slight boosting or cutting of particular
voice frequencies can really make a difference to clarity. There are three
sections giving the sort of control usually only found on much larger
mixers. The EQ knobs can have a dramatic effect, so use them sparingly
and listen carefully as you change any settings so that you get to know
how they affect the sound.
HF EQ
Turn to the right to boost high (treble) frequencies above 12kHz by up to
15dB, adding crispness to cymbals, vocals and electronic instruments.
Turn to the left to cut by up to 15dB, reducing hiss or excessive sibilance
which can occur with certain types of microphone. Set the knob in the
centre-detented position when not required.
MID EQ
There are two knobs which work together to form a SWEPT MID EQ. The
lower knob provides 15dB of boost and cut, just like the HF EQ knob, but
the frequency at which this occurs can be set by the upper knob over a
range of 150Hz to 3.5kHz. This allows some truly creative improvement
of the signal in live situations, because this mid band covers the range
of most vocals. Listen carefully as you use these controls together to
nd how particular characteristics of a vocal signal can be enhanced or
reduced. Set the lower knob to the centre-detented position when not
required.
LF EQ
Turn to the right to boost low (bass) frequencies below 80Hz by up to
15dB, adding warmth to vocals or extra punch to synths, guitars and
drums. Turn to the left to cut low frequencies by up to 15dB for reducing
hum, stage rumble or to improve a mushy sound. Set the knob to the
centre-detented position when not required.
6 Aux 1 Send
This is used to set up a separate mix for FOLDBACK or recording, and the
combination of each Aux Send is mixed to the Aux1 Output. For recording
it is useful for the signal to fade up and down with the fader (this is called
POST-FADE), but for Foldback or Monitor feeds it is important for the send
to be independent of the fader (this is called PRE-FADE).
AUX 1 SEND is globally switchable between pre and post-fade (see master
section on page 24/25).
7 FX Send (EFX only)
This control sets the level of the post-fade signal being sent to the FX
bus; from there it is routed to the FX processor.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft EPM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft EPM in the language / languages: English as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info