611452

Soundcraft EPM Manual

22
Zoom out
Zoom in
Previous page
1/60
Next page
20
Soundcraft EFX/EPM User Guide Issue 1210
7 Aux 2 Send (EPM only)
This is used to set up a separate mix for FOLDBACK or recording, and the
combination of each Aux Send is mixed to the Aux 2 Output. For record-
ing it is useful for the signal to fade up and down with the fader (this is
called POST-FADE), but for Foldback or Monitor feeds it is important for
the send to be independent of the fader (this is called PRE-FADE).
AUX 2 SEND is globally switchable between pre and post-fade (see master
section on page 24/25).
8 PAN
This control sets the amount of the channel signal feeding the Left and
Right MIX buses, allowing you to move the source smoothly across the
stereo image. When the control is turned fully left or right you are able
to route the signal at unity gain to either left or right outputs individually.
9 MUTE
All outputs from the channel except inserts are on when the MUTE switch
is released and muted when the switch is down, allowing levels to be
pre-set before the signal is required.
10 INPUT CHANNEL FADER
The 60mm FADER, with a custom-designed law to give even smoother
control of the overall signal level in the channel strip, allows precise bal-
ancing of the various source signals being mixed to the Master Section.
You get most control when the input GAIN is set up correctly, giving full
travel on the fader. See the “Initial Setup” section on page 36 for help
in setting a suitable signal level.
11 PFL
When the latching PFL switch is pressed, the pre-fade pre-mute signal is
fed to the headphones, control room output and meters, where it replaces
the MIX. The PFL ACTIVE LED on the Master section illuminates to warn
that a PFL is active. This is a useful way of listening to any required input
signal without interrupting the main mix, for making adjustments or trac-
ing problems. When PFL is pressed anywhere on the console, the Control
Room outputs automatically switch from monitoring the Mix Outputs.
12 PEAK LED
This LED will light when the signal level approaches clipping at any of the
three monitored points:
a) PRE-EQ
b) POST-EQ
c) POST-FADE
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Soundcraft EPM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Soundcraft EPM in the language / languages: English as an attachment in your email.

The manual is 3,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info