812376
20
Zoom out
Zoom in
Previous page
1/28
Next page
Pump settings / Signal V1
In this menu, the settings for the speed controlled output V1 are executed.
Type of pump/ Type of signal
The type of speed controlled pump used can be set here.
0-10V: Control of special pumps (e.g. high efficiency pumps) through a 0-10V signal.
PWM: Control of special pumps (e.g. high efficiency pumps) through a PWM signal.
Pump/ Profile
In this menu, the preset profiles for the pump can be selected or under “manual all settings can be done personally. The settings can
still be changed after a profile has been selected.
Output Signal
In this menu, the type of pump is set: heating pumps have the greatest output with a small input signal, solar pumps in contrast have very
little output with a small input signal. Solar = normal, heating = inverted.
PWM / 0-10V off
This signal / this voltage is emitted if the pump is turned off (pumps with cable break detection require a minimal voltage / a minimum sig-
nal).
PWM / 0-10V on
This voltage / this signal requires the pump in order to turn on and to run at a minimum speed.
PWM / 0-10V max.
With this value, the maximum voltage level / maximum frequency can be specified for the highest speed of the energy saving pump,
which is used, for example, during the flushing or manual operation.
Show signal
Represents the set pump signal in a graphic and text overview.
Speed control
If the speed control is activated, itMTDC-E offers the possibility through a special internal electronic system to change the speed of
pumps depending on the process.
This function should only be activated by a technician. Depending on the pump being used and the pump level, the minimum
speed may not be set too small, because the pump or the system may be damaged. The specifications from the affected man-
ufacturer must be observed for this! When in doubt, the min. speed and the pump level should be set too high instead of too
low.
Variant
The following speed variants are available here:
Off: There is no speed regulation. The connected pump is only turned on or off with full speed.
Mode M1: The controller changes to the set max. speed after the purging time. If the temperature difference ∆T between the reference
sensors is below the set switch on temperature difference ∆T Solar, the speed will be reduced. If the temperature difference between the
reference sensors is above the set switch on temperature difference ∆T Solar, the speed will be increased. If the controller has
decreased the speed of the pump to the smallest level and the ∆T between the reference sensors is still only Toff, the pump will be
turned off.
Mode M2: The controller changes to the set min. speed after the Speed. If the temperature difference ∆T between the reference sensors
is above the set switch on temperature difference ∆T Solar, the speed will be increased. If the temperature difference ∆T between the ref-
erence sensors is below the set switch on temperature difference ∆T Solar, the speed will be reduced. If the controller has decreased
the speed of the pump to the smallest level and the ∆T between the reference sensors is still only Toff, the pump will be turned off.
Mode M3: The controller changes to the set min. speed after the Speed. If the temperature on the reference sensors is above the set
value to be set in the following, the speed will be increased. If the temperature on the reference sensors is below the set value to be set
in the following, the speed will be reduced.
20
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel MTDC-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel MTDC-E in the language / languages: English as an attachment in your email.

The manual is 3.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel MTDC-E

Sorel MTDC-E User Manual - German - 26 pages

Sorel MTDC-E User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info