812376
22
Zoom out
Zoom in
Previous page
1/28
Next page
Example: displayed collector temperature 40°C, read previous temperature 39°C, displayed storage temperature 30°C, read return tem-
perature 3 means a setting of -20% (displayed ∆T 10K, actual T 8K => -20% correction value)
Sensor Calibration
Deviations in the temperature values displayed, for example. due to cables which are too long or sensors which are not positioned
optimally can be compensated for manually here. The settings can be made for each individual sensor in steps of 0.5 °C.
Settings are only necessary in special cases at the time of initial commissioning by the specialist. Incorrect measurement val-
ues can lead to unpredictable errors.
Commissioning
Starting commissioning help guides you in the correct order through the basic settings necessary for commissioning, and provides brief
descriptions of each parameter in the display. Pressing the esc‘ key takes you back to the previous value so you can look at the selec-
ted setting again or adjust it if desired. Pressing esc‘ more than once takes you back to the selection mode, thus cancelling the com-
missioning help (See " Commissioning help " on page 13).
May only be started by a specialist during commissioning! Observe the explanations for the individual parameters in these
instructions, and check whether further settings are necessary for your application.
Factory Settings
All settings can be reset, returning the controller to its delivery state.
All of the controller‘s parametrization, statistics, etc. will be lost irrevocably. The controller must then be commissioned once
again.
Starting aid
For some solar systems, in particular for vacuum tube collectors, the measurement recording on the collector sensors may be too slow
or imprecise, because the sensor is often not on the warmest spot. With an activated starting aid, the following procedure occurs: If the
temperature on the collector sensor increases within a minute by the value defined under “increase”, the solar circulation pump will be
turned on for the set “purging time so that the medium to be measured is transported to the collector sensor. If there is still no normal
switching condition through this, there will be a 5 minute block time for the start wizard function.
This function should only be activated by a technician if problems occur with the measurement recording. Observe in par-
ticular the instructions from the collector manufacturer.
The menus "Purging time" and "Increase" are only displayed when the starting aid function is set to "On".
Purging time
If the temperature on the collector sensor increases within a minute by the value defined under “increase”, the solar circulation pump will
be turned on for the set “purging time so that the medium to be measured is transported to the collector sensor. If the set ΔT is not
reached, a 5-minute circulation pause time for the starting aid function will apply.
Increase
If the temperature at the collector reaches within a minute the value defined, the solar pump is turned on for the duration of the purging
time.
Time & Date
Serve to set the current time and date.
22
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel MTDC-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel MTDC-E in the language / languages: English as an attachment in your email.

The manual is 3.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel MTDC-E

Sorel MTDC-E User Manual - German - 26 pages

Sorel MTDC-E User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info