812376
16
Zoom out
Zoom in
Previous page
1/28
Next page
4. Settings
By no means does the controller replace the safety appliances on site!
Tmin S1
Enable/start temperature at sensor 1:
If this value on the sensor 1 (collector sensor) is exceeded and the other conditions are not fulfilled, the controller will turn on the affil-
iated pump or the valve. If the temperature on the sensor 1 falls 5 °C below this value, the pump or the valve will be turned off again.
ΔT Solar S(X)
Switch-on/switch-off temperature difference for sensor X: If the temperature difference ΔT solar between the reference sensors is
exceeded and the other conditions are fulfilled, the controller will turn on the pump/valve on the corresponding relay. If the temperature
difference falls to ΔT Off, the pump/valve will be turned off again.
If the set temperature difference is too small, this may lead to ineffective operation depending on the system and sensor pos-
itioning. For speed regulation (See " Speed control " on page 20), special switch conditions apply!
Tmax S2
Switch off temperature at sensor 2:
If this value is exceeded on the sensor 2, the controller turn off the affiliated pump or the valve. If this value on the sensor 2 is undershot
and the other conditions are fulfilled, the controller will turn on the pump or the valve.
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be
provided by the customer!
In multiple storage systems, if the shut-down temperature S2 is exceeded, a downstream installed storage or storage area is switched
to.
Auxiliary heating
All required settings for the auxiliary heating are done here.
Tset
If this value is fallen below at the sensor of the function, the controller switches on the auxiliary heating. The auxiliary heating is switched
off if this value is exceeded by the set hysteresis.
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be
provided by the customer!
Other values, for example, Teco, apply in economy mode.
Hysteresis
The hysteresis can be used to determine the heating of the storage. If the value Tset at sensor (e.g. S3) is exceeded by the set hys-
teresis, the controller switches off the additional heating.
16
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel MTDC-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel MTDC-E in the language / languages: English as an attachment in your email.

The manual is 3.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel MTDC-E

Sorel MTDC-E User Manual - German - 26 pages

Sorel MTDC-E User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info