812338
33
Zoom out
Zoom in
Previous page
1/44
Next page
If the temperature difference between the sensors defined for this function exceeds the value set here (ΔT SF On), the function
switches on the assigned output (relay or signal output).
If the set temperature difference (ΔT SF Off) between the solids boiler and the storage tank is below, the function switches off the
assigned output (relay or signal output).
Boiler sensor of this function
Sensor used as a solids boiler sensor. Considered for SF Tmin and ΔTon/off.
Storage sensor
Sensor used as a storage tank sensor. Considered for FS Tmax and ΔTon/off.
Solar
This function is used to control a solar pump.
Tmin Collector
Enable/start temperature at sensor X:
If this value on the specified sensor is exceeded and the other conditions are not fulfilled, the controller will turn on the affiliated
pump or the valve. If the temperature on the sensor falls 5 °C below this value, the pump or the valve will be turned off again.
ΔT Solar
Switch on/switch off temperature difference for sensor X:
If the temperature difference ΔT Solar between the reference sensors is exceeded and the other conditions are fulfilled, the con-
troller will turn on the pump/valve on the corresponding relay. If the temperature difference falls to ΔT Off, the pump/valve will be
turned off again.
Tmax Storage
Switch off temperature at sensor X:
If this value is exceeded at the specified sensor, the controller turn off the affiliated pump or the valve. If this value on the sensor is
undershot and the other conditions are fulfilled, the controller will turn on the pump or the valve.
Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be
provided by the customer!
Starting aid
For some solar systems, in particular for vacuum tube collectors, the measurement recording on the collector sensors may be too
slow or imprecise, because the sensor is often not on the warmest spot. With an activated starting aid, the following procedure
occurs: If the temperature on the collector sensor increases within a minute by the value defined under “increase”, the solar cir-
culation pump will be turned on for the set “purging time so that the medium to be measured is transported to the collector
sensor. If there is still no normal switching condition through this, there will be a 5 minute block time for the start wizard function.
This function should only be activated by a technician if problems occur with the measurement recording. Observe in
particular the instructions from the collector manufacturer.
The menus "Purging time" and "Increase" are only displayed when the starting aid function is set to "On".
Purging time
If the temperature on the collector sensor increases within a minute by the value defined under “increase”, the solar circulation
pump will be turned on for the set “purging time so that the medium to be measured is transported to the collector sensor. If the
set ΔT is not reached, a 5-minute circulation pause time for the starting aid function will apply.
Increase
If the temperature at the collector reaches within a minute the value defined, the solar pump is turned on for the duration of the
purging time.
Protective Functions
see " Protective functions for Solar " on page 22
33
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel LHCC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel LHCC in the language / languages: English as an attachment in your email.

The manual is 8.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel LHCC

Sorel LHCC User Manual - German - 46 pages

Sorel LHCC User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info