680840

Sommer Sprint S550N de Luxe Manual

14
Zoom out
Zoom in
Previous page
1/30
Next page
GB
11
Installing the Garage Door Drive Mechanism
•
Determine the door’s highest up-position:
Open the door and measure the minimum clearance between
the upper edge of the door and the ceiling. This clearance must
be at least 30 mm. The lower edge of the C-rail must be higher
than the door’s highest up-position.
•
The garage door drive mechanism can be installed on the lintel
(S) or on the ceiling (D).
•
Measure the door forward centre point (VM) and mark it on the
door and lintel or ceiling.
•
Make a mark 74 mm to the right and left of the door centre point
(VM) at the same height on the lintel or ceiling (see Figure 16).
•
Drill two holes (Ø 10 x 65 mm deep).
Caution: check the thickness of the ceiling
•
Open the door, transfer the mark from the door centre point
to the ceiling (HM), close the door.
•
Insert wall plug (1), lift garage door drive mechanism (2) at the
front. Secure retaining catch (3) at the front with two screws
(4) and plain washers (5).
•
Lift garage door drive mechanism at the back.
•
Align ceiling bracket (1). Its location must be in area (B).
B = 0 bis 600 mm
Use a non-slip, stable stepladder.!
•
Align garage door drive mechanism horizontally relative to HM.
Mark position of holes. Drill two holes (Ø 10 x 65 mm deep).
Caution: check the thickness of the ceiling
•
Insert wall plug (1). Prepare two screws (2) with plain
washers (3) and tighten the screws securely.
•
Align C-rail (4) at correct height. If necessary, move screws
(5).
•
Assemble push rod (1):
insert bold (2) and put on retainer (3).
•
Pull once on emergency release cordl (N).
This unlocks bogie truck (1).
•
Use push rod (2) to push bogie truck (1) all the way forward
(3). If necessary, loosen cut-out buffer (4) to do this.
15
16
•
Align door-fitting bracket (5) with the centre of the door and
mark out 5 holes. Drill 5 holes (Ø 5 mm).
Use screws that are appropriate for the door material in
question.
Wear safety glasses when drilling!
•
Insert 5 hexagon head cap screws (6) and tighten them
securely.
•
Loosen cut-out buffer (4) and push firmly on bogie truck (7).
•
Tighten screw of cut-out buffer (4).
•
Loosen rear cut-out buffer (1) and push it back as far as the
stop (2). Open the door (3) by hand.
Shorten the ceiling bracket if necessary (4).
•
Push cut-out buffer (1) onto bogie truck (5) as far as the stop
(6). Tighten the screw on the cut-out buffer.
Installing the Slip Door Safety System and
Emergency Release Lock
•
There is a slip door in the door but no slip door safety system - install
a slip door safety system (see instructions for accessories).
•
There is no slip door in the door and no second entrance to the
garage - install an emergency release lock or Bowden pull wire as an
external release device (see instructions for accessories).
Installing and Connecting the Switches
The user must not be in the door’s area of movement
when the switch is operated. The user must have an
unobstructed view of the door.
•
Install switch (1) in an appropriate, easily accessible
location in the garage. Minimum height from
floor - 1.6 m.
Do not install the switch within the door’s area of
movement.
•
Install connection cable (2) in the garage.
Connect the end of the cable to the switch.
17
18
19
20
22
21
23
24
25
•
Disassemble push rod (1); pull retainer (2) out,
remove bolt (3)
26
27
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Sprint S550N de Luxe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Sprint S550N de Luxe in the language / languages: English, German, French as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info