Manual Sommer Sprint 550SL (page 22 of 36) (English)

474211

Zoom out

Zoom in

1/36

Operation and Handling

Interim stop

If an interim stop occurs due to the operation of a push-button or the

manual remote control, the drive unit stops immediately. The next command

given sends the drive in the opposite direction. See 'Pulse Sequence of

Door Movement' section.

Safety stop 1

(automatic force cut-off)

When the automatic force cut-off is activated, the drive stops or reverses.

When the next command is given, the drive moves in the opposite direction.

See 'Pulse Sequence of Door Movement' section.

- Safety stop when door closes - door reverses

- Safety stop when door opens - door stops.

Safety stop 2

(automatic force cut-off)

When the safety input is tripped (e.g. someone crosses light barrier), the

drive stops, reverses or opens, depending on the given DIP switch setting:

- DIP switch 1 + 3

See 'Obstacle Recognition' section for given drive type.

When the next command is given, the drive moves in the opposite direction.

See 'Pulse Sequence of Door Movement' section.

Default settings:

- safety input tripped when door closes:

door reverses

- safety input tripped when door opens:

no response (door opens).

Overload protection

If the drive mechanism is subjected to excessive strain when opening or

closing the door, this is recognised by the control unit which then stops the

drive mechanism. After approx. 20 seconds or a control unit reset, the

control unit deactivates the overload protection.

The drive mechanism can now recommence normal operation.

Operation following a power failure

The force values remain saved even during a power failure. The first

movement of the unit following a power cut is always door OPEN.

Radio remote control receiver

Homelink compatible!

If your vehicle is equipped with a Homelink system (version 7),

you can reach our drive/radio receiver at 868.6 MHz. With holder

Homelink systems, you must use a different frequency (40.685 or

434.42 MHz). For more information, please visit:

"http://www.eurohomelink.com"

• To ensure safe operation, local safety regulations relevant to the

equipment concerned must be observed! Information regarding this can

be obtained from electricity suppliers, the VDE and employers' liability

insurance associations.

• The operator of this radio-controlled equipment is in no way protected

from interference from other telecommunications systems and facilities

(e.g. other radio-controlled equipment that is licensed to operate at the

same frequency range).

• Try replacing the batteries should reception problems be encountered.

Description of display and

push-buttons

1 Setting button

Puts radio receiver in a given operating mode:

self-learn, delete and normal

2 Internal aerial

3 LED

Display which channel has been selected.

3.1 LED channel 1

3.2 LED channel 2

4 Connection for external aerial (6)

If the radio range of the internal aerial is not sufficient, you have

the option to connect an external aerial.

5 Manual remote control button

6 External aerial

Teaching in manual remote control

• Press setting button (1)

- Press 1x for channel 1; LED (3.1) lights up

- Press 2x for channel 2; LED (3.2) lights up

- If no radio code is transmitted within 10 seconds, the receiver

switches back to normal operating mode.

- Interrupting setting mode: press setting button (1) as often as

required to put out all LEDs

• Press and hold desired hand-held transmitter key until the LED (3.1 /

3.2) is off - depending on the selected channel.

• The LED is off - the programming process is completed.

The hand-held transmitter has transmitted the radio code to the radio

receiver.

Teaching in further manual remote controls. Repeat above steps.

Max. 112 memory slots are available per radio receiver.

Deleting manual remote control

button from radio receiver

If a user of a multi-user garage facility moves house and wants to take his

manual remote control with him, then all the codes of the given user's

manual remote control have to be deleted from the radio receiver.

For security reasons, each manual remote control button and/or

combination of buttons should be deleted!

• Press setting button (1) and keep depressed for 5 seconds until an

LED starts to flash (any LED).

• Release setting button (1) - radio receiver is in delete mode.

• Press push-button on the manual remote control, the one whose

code is required to be deleted on the radio receiver - LED goes out -

deletion process complete.

Repeat procedure for all push-buttons and combination of buttons.

3.1

3.2

3.1

3.2

Hi I have a sprint 550sl overhead door opener. The light keeps flashing I can close the door with the wall switch or the hand remote but I cannot open the door it is just no reaction whatsoever with the wall or the hand remotes totally dead. Can you possibly suggest what could be causing the problem. Many thanks. Submitted on 5-7-2023 at 12:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Sprint 550SL in the language / languages: English as an attachment in your email.

The manual is 4,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Sprint 550SL

Sommer Sprint 550SL User Manual - German - 37 pages

Sommer Sprint 550SL User Manual - Dutch - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sommer Sprint 550SL Manual

Product: