680782
58
Zoom out
Zoom in
Previous page
1/88
Next page
58
S10931-00001_Rev-D_EN
11. Connections and special functions of the wall
control unit
Installing the keypad
1. When installing the potential-free keypad, select
a suitable position at a height of at least 1.6 m.
2. Install the keypad.
3. Route the keypad cable to the wall control unit and
secure it firmly to prevent displacement.
Installing the control cable and settings on the
wall control unit
1. Disconnect the operator from the mains voltage.
Check it is disconnected from the power supply.
2. Unscrew the light cover from the wall control unit
and remove it upwards. Hold the front cover firmly
while doing so.
3. Remove the control unit cover gently towards
the front and unplug the connection cable for
the membrane keypad from the wall control unit,
see chapter "7.3 Light and control unit cover of
the wall control unit."
4. If an accumulator is used, it must also be
disconnected, see Chapter "11.12 Installing and
removing the accumulator."
5. Remove the control unit cover.
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
G
N
D
+24
V
ON
1234
Fig. 6 Fig. 7
6. Connect the cable of button 2 to the terminal block
for COM and Signal.
Button 2 is connected.
7. Set DIP switch 4 on the wall unit to "ON."
8. Plug in the connection cable for the button and
for the accumulator, if necessary.
9. Close the ceiling control unit in reverse order,
see chapter "11.12 Installing and removing the
accumulator" and "7.3 Light and control unit
cover of the wall control unit."
10. Supply the operator with the mains voltage.
Check that the power supply is connected.
Settings on the motor carriage
To determine the partial opening door position, the
following settings must be made on the motor carriage.
1. Close the door completely up to the door CLOSE
end position.
2. Open the motor carriage, see chapter "7.1 Cover of
the motor carriage."
3. Set DIP switch 2 on the motor carriage to "ON."
4. Press button 2 for the partial opening function.
The door moves in door OPEN direction.
5. Press button 2 again for the desired position for
stopping.
The door stops at the desired position.
11.6 Deleting partial opening
1. Set DIP switch 2 on the motor carriage to "OFF."
2. Open the door completely up to the door OPEN
end position.
Partial opening is deleted.
To program a new position, see chapter "10.17 Setting
partial opening."
11.7 Photocell and frame photocell
A 2-wire photocell from SOMMER or a 4-wire photocell
can be connected to the control unit. The control unit
automatically detects which version it is and sets itself
to that version.
Fig. Terminal for a 2-wire photocell
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
Fig. Terminal for a 4-wire photocell
INFORMATION
If a photocell is retrotted on
a programmed system, the control
unit must be reset, see chapter
"10.13 Performing a reset."
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9080 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 pro

Sommer S 9080 pro User Manual - German - 88 pages

Sommer S 9080 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info