474213
25
Zoom out
Zoom in
Previous page
1/36
Next page
Functions and Connections marathon
24
Automatic close mode (DIP 4)
Observe standard EN 12453 (e.g. fit light barrier 1) for automatic
close mode. An additional light barrier can be connected to
safety connection 2 as upper safety limit.
Caution !
Connect the small door fuse to the safety input 2 (terminals
8 + 9). If the small door fuse is connected to the trolley, the drive
is unable to detect the position of the door.
Door closes automatically after door open period set on potentiometer has
elapsed. The door can only be opened by means of a command issued via
a push-button or manual remote control. When the door is opening, no
command issued can stop it from doing so.
When it is closing automatically and a further command is issued, the door
opens fully. Any command issued during the door open period, restarts the
given set period.
In automatic close mode, the partial opening function is
deactivated.
Activating and deactivating door open period with potentiometer:
- period can be set from 1 to 120 seconds
- deactivate by turning potentiometer as far anticlockwise as possible.
Behaviour of drive when safety inputs 1 + 2 are tripped
When door is closing:
Drive always opens door fully, irrespective of DIP switch 3 setting
When door is opening:
Behaviour of door in accordance with DIP switch 1 setting.
Two-way traffic system with lights
Disconnect the internal lighting and do not reconnect.
Both red lights show the same behaviour when the door is in motion.
- Outside red light: terminals 16 + 17, installed outside the garage
- Inside red light: terminals 18 +19, installed inside the garage
Automatic close mode, option 1
The automatic CLOSE mode is automatically activated when the door
reaches the OPEN final travel position. The period set via the potentiometer
starts running from this moment onwards. A command given during the
door OPEN period restarts the given set period.
Settings:
- Potentiometer set to required time (1 - 120 seconds)
- DIP switches 7 + 8 OFF
- Other DIP switches set as required
Automatic close mode + light barrier, option 2
Interrupt automatic closing manually by installing switch in the
light barrier's supply cable.
As described above, apart from the fact that the drive mechanism closes
the door 5 seconds after the light barrier has been crossed.
Settings:
- Potentiometer set to required time (1 - 120 seconds)
- DIP switches 1, 7 + 8 OFF
- DIP switch 4 ON
- Other DIP switches set as required
Automatic close mode + safety contact strip (8,2 kOhm /
Fraba) + light barrier, option 3
Interrupt automatic closing manually by installing switch in the
light barrier's supply cable.
As described above, apart from the fact that the drive mechanism closes
the door 5 seconds after the light barrier has been crossed.
Connect the light barrier in series to the safety contact strip to terminals
6 + 7.
Settings:
- Potentiometer set to required time (1 - 120 seconds)
- DIP switches 1, 7 + 8 OFF
- DIP switch 2, 4 ON
- Other DIP switches set as required
Terminal bar, 24-pole
Permissible cable cross-section: max. 1,5 mm².
Terminal 1 Antenna connection 40 MHz
2 + 3 Push-button 1 (potential-free NO contact) *
4 + 5 Push-button 2 (potential-free NO contact)
6 + 7 Safety input 1 (bridge) *
8 + 9 Safety input 2 (bridge) *
10 + 11 Regulated 24 V DC, max. 0.1 A
12 + 13 Chain (12) + C-rail (13) *
14 + 15 Transformer, secondary *
16 + 17 Warning light 1, unregulated 24 V/DC
18 + 19 Internal light/warning light 2, unregulated 24 V/DC *
20 + 21 Regulated 12 V/DC
22 free
23 + 24 Potential-free relay output 230 V AC, max. 5 A
* Factory settings
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
12
14
18
3
13
15
19
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Duo 650SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Duo 650SL in the language / languages: English as an attachment in your email.

The manual is 4,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Duo 650SL

Sommer Duo 650SL User Manual - German - 37 pages

Sommer Duo 650SL User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info