474213
22
Zoom out
Zoom in
Previous page
1/36
Next page
Operation and Handling
21
Interim stop
If an interim stop occurs due to the operation of a push-button or the
manual remote control, the drive unit stops immediately. The next command
given sends the drive in the opposite direction. See 'Pulse Sequence of
Door Movement' section.
Safety stop 1
(automatic force cut-off)
When the automatic force cut-off is activated, the drive stops or reverses.
When the next command is given, the drive moves in the opposite direction.
See 'Pulse Sequence of Door Movement' section.
- Safety stop when door closes - door reverses
- Safety stop when door opens - door stops.
Safety stop 2
(automatic force cut-off)
When the safety input is tripped (e.g. someone crosses light barrier), the
drive stops, reverses or opens, depending on the given DIP switch setting:
- DIP switch 1 + 3
See 'Obstacle Recognition' section for given drive type.
When the next command is given, the drive moves in the opposite direction.
See 'Pulse Sequence of Door Movement' section.
Default settings:
- safety input tripped when door closes:
door reverses
- safety input tripped when door opens:
no response (door opens).
Overload protection
If the drive mechanism is subjected to excessive strain when opening or
closing the door, this is recognised by the control unit which then stops the
drive mechanism. After approx. 20 seconds or a control unit reset, the
control unit deactivates the overload protection.
The drive mechanism can now recommence normal operation.
Operation following a power failure
The force values remain saved even during a power failure. The first
movement of the unit following a power cut is always door OPEN.
Radio remote control receiver
Homelink compatible!
If your vehicle is equipped with a Homelink system (version 7),
you can reach our drive/radio receiver at 868.6 MHz. With holder
Homelink systems, you must use a different frequency (40.685 or
434.42 MHz). For more information, please visit:
"http://www.eurohomelink.com"
To ensure safe operation, local safety regulations relevant to the
equipment concerned must be observed! Information regarding this can
be obtained from electricity suppliers, the VDE and employers' liability
insurance associations.
The operator of this radio-controlled equipment is in no way protected
from interference from other telecommunications systems and facilities
(e.g. other radio-controlled equipment that is licensed to operate at the
same frequency range).
Try replacing the batteries should reception problems be encountered.
Description of display and
push-buttons
1 Setting button
Puts radio receiver in a given operating mode:
self-learn, delete and normal
2 Internal aerial
3 LED
Display which channel has been selected.
3.1 LED channel 1
3.2 LED channel 2
4 Connection for external aerial (6)
If the radio range of the internal aerial is not sufficient, you have
the option to connect an external aerial.
5 Manual remote control button
6 External aerial
Teaching in manual remote control
Press setting button (1)
- Press 1x for channel 1; LED (3.1) lights up
- Press 2x for channel 2; LED (3.2) lights up
- If no radio code is transmitted within 10 seconds, the receiver
switches back to normal operating mode.
- Interrupting setting mode: press setting button (1) as often as
required to put out all LEDs
Press and hold desired hand-held transmitter key until the LED (3.1 /
3.2) is off - depending on the selected channel.
The LED is off - the programming process is completed.
The hand-held transmitter has transmitted the radio code to the radio
receiver.
Teaching in further manual remote controls. Repeat above steps.
Max. 112 memory slots are available per radio receiver.
Deleting manual remote control
button from radio receiver
If a user of a multi-user garage facility moves house and wants to take his
manual remote control with him, then all the codes of the given user's
manual remote control have to be deleted from the radio receiver.
For security reasons, each manual remote control button and/or
combination of buttons should be deleted!
Press setting button (1) and keep depressed for 5 seconds until an
LED starts to flash (any LED).
Release setting button (1) - radio receiver is in delete mode.
Press push-button on the manual remote control, the one whose
code is required to be deleted on the radio receiver - LED goes out -
deletion process complete.
Repeat procedure for all push-buttons and combination of buttons.
5
T2
2
4
6
3.1
3.2
1
7
8
4
5
6
5
2
6
4
3.1
3.2
1
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Duo 650SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Duo 650SL in the language / languages: English as an attachment in your email.

The manual is 4,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Duo 650SL

Sommer Duo 650SL User Manual - German - 37 pages

Sommer Duo 650SL User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info