655794
28
Zoom out
Zoom in
Previous page
1/97
Next page
Starting / Stopping the engine ; Operation hints
ENGLISH 12
11. Starting / Stopping the engine
1. Open fuel valve (ON).
2. Push primer (Fig A) until float-chamber is filled
with fuel (only when engine is cold).
3
. Switch ignition switch to ”I” position and close
liquid tap.
4. Close choke (Fig. 5 - B)
only when engine is cold.
5. Start engine with recoil starter. DO NOT yank
starter suddenly; first pull starter rope until
pawls engage (resistance of recoil spring is
felt). Lead starter grip slowly back to starter
housing.
6. Open choke as soon as the engine fires
and "tries" to start. Repeat the starting
procedure if required.
Shutting off engine
Release throttle lever and move ignition switch
to ”Stop” position until engine stops.
12. Operation hints
Before every use and before every start of the
mistblower check and ensure the machine is in
good and safe condition. (throttle operation,
ignition switch, safety devices, shoulder strap
and check for fuel leaks)
During the starting procedure and while
operating the mistblower, the operator must
have secure footing and have a safe body
position.
The engine starting site should be at least 3
meters away from the refueling site.
12.1 Spraying
Open liquid tap: Lever in horizontal position ON
Shut liquid tap: Lever in vertical position OFF
The correct output is obtained according to
dosage-sleeve setting
When spraying predominantly upwards (tall trees)
we recommend using the liquid pump offered as an
accessory (part no.: 44 00 117)
Misting Output Guide
Dosage
sleeve
A *) B C
Position 1 0,32 L/min 0,17 L/min 0,33 L/min
Position 2 0,63 L/min 0,31 L/min 0,54 L/min
Position 3 1,03 L/min 0,54 L/min 1,04 L/min
Position 4 1,46 L/min 0,65 L/min 1,42 L/min
*) The delivery values when using a liquid pump
(accessories) apply to every position of the spray
wand.
Note: The liquid pump attachment comprises a
special metering body, which should be installed
when using a liquid pump.
Please note: When using a liquid pump, ensure
that the tank contains sufficient liquid. The
liquid pump can sustain severe damage, if it is
permitted to run dry. When using the
equipment as a mister and as blower, remove
the pump for that reason.
Fig. 6
Fig. 5
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo Port 423 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo Port 423 in the language / languages: Dutch, Italian as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Solo Port 423

Solo Port 423 User Manual - English, German, French, Spanish - 62 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info