655959

Solo 880 Manual

68
Zoom out
Zoom in
Previous page
1/249
Next page
Power tool use
ENGLISH 26
Always observe all safety notes and all other information in all chapters of these operating
instructions for any work!
Check list for use (keywords only!) ................................................. Î
x Before start-up:
– Power tool in an operationally safe condition! ....................... ÎOperating instructions complete
– Prescribed work clothes ........................................................ ÎChap. 3.3, page 7
– Working area inspected and secured .................................... Î Chap. 3.2, page 6, and
chap. 3.9, page 10
– Correct cut-off wheel firmly installed. ..................................... ÎChap. 5.1, page 16, and
chap. 7.1, page 26
– Wheel guard in best position ................................................. ÎChap. 5.4, page 18
– Cutting device position, preferably centre position ................ Î Chap. 5.8, page 21
– Ribbed belt tension correct .................................................... Î Chap. 5.6, page 20
– Tool properly fuelled .............................................................. Î Chap. 5.5, page 18
x Starting: ....................................................................................... ÎChap. 6 complete, as of page 24
– Starting preparations ............................................................. ÎChap. 6.1, page 24
Stop dial in operating position .......................................... ÎChap. 6.1, page 24
x During work – generally safe work: ............................................. Î Operating instructions complete
– Check idle settings ................................................................ Î Chap. 8.3, page 32
– Inspecting the working situation ............................................ Î Chap. 3.9, page 10,
Chap. 7.2, page 27, and
Chap. 7.3, page 28
– Wet cutting preferred ............................................................. ÎChap. 5.7, page 20
– Secure working technique ..................................................... ÎChap. 7.3, page 28,
chap. 7.4, page 28, and
chap. 7.5, page 29
– Operating and maintenance notes complete ......................... Î Chap. 8 complete, as of page 30
Air filter clean ................................................................... ÎChap. 8.4, page 33
x After work: ...................................................................................
Î Operating instructions complete
– Cleaning and care ................................................................. ÎChap. 8.1, page 30
– Secure storage of power tool ................................................. ÎChap. 8.10, page 39
– Maintenance .......................................................................... Î Operating instructions complete
Only use cut-off wheels that correspond to the standards ANSI B7.1, EN 12413 and EN 13236 and
that are undamaged.
The maximum spindle speed of the power tool is 4,550 min
-1
[4,550 rpm].
Only use high speed reinforced cut-off wheels marked with a permissible maximum operating speed
of at least 4,550 min
-1
[4,550 rpm].
For processing of metals (hot cutting) and processing of mineral materials (cold cutting), different cut-off
wheels are offered. Only use cut-off wheels approved for the material being cut.
7 Power tool use
7.1 Cut-off wheels
… 68 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 880 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info