655959

Solo 880 Manual

70
Zoom out
Zoom in
Previous page
1/249
Next page
Power tool use
ENGLISH 28
x For complex cutting processes, cutting direction and order of the cuts to be performed must be specified
in advance to prevent pinching of the cut-off wheel by the removed part and injury from dropping parts.
x Always hold the power tool with both hands. Have the right hand on the rear handle, the left hand on the
top handle. Firmly grasp the handles with your thumb.
x Operate the power tool at high speed when possible.
x Direction change (cutting radius below 5 m [approx. 15 ft]), side pressure, twisting or tilting of the power
tool during cutting is forbidden.
x When shortening work pieces use a secure support and secure the work piece against slipping and
twisting. The work piece must not be held with your foot or by another person.
x Always be ready for sudden kickback of the work piece and warrant the possibility of securely backing
away.
x Make sure that cut-off sections cannot fall resulting in injury or property damage.
Always wear breathing protection equipment at dry cutting.
Metals are heated and melted at the point of contact by the fast rotation of the cut-off wheel.
x Rotate the wheel guard down as far as possible for sparks to fly forward where possible, i.e. away from
the user.
x Before cutting, specify and mark the cutting joint, and approach the material with the cut-off wheel at
medium speed. Only when the guide groove is cut, continue cutting at full throttle and increased
pressure.
x Only cut straight and vertically. Do not tilt or twist.
x For a secure and smooth cut, it is best to pull or to move the power tool in a controlled fashion. When
moving the power tool, do not push the cut-off wheel into the material in addition to the thrust caused by
the wheel's rotation.
x Large diameter round rods are best cut in steps.
x Thin tubes can be cut with a single sinking cut.
x Tubes with large diameters should be treated like large diameter rods. To avoid tilting and for better
control of the cutting process, do not let the cut-off wheel sink into the material too far. Do not allow the
mounting flanges of the cut-off wheel fastening to come into contact with the work piece. Always cut flat
around.
x Double-T carriers or angled steel should be cut in steps.
x Steel bands or steel plates are cut like tubes; pulling flat with long cutting area.
x Material under stress (supported or material in a wall) always has to be grooved slightly on the
compression side and then cut from the tension side so that the cut-off wheel is not pinched.
7.3 Working behaviour and working technique
7.4 Cutting metal
… 70 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 880 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info