655955
66
Zoom out
Zoom in
Previous page
1/160
Next page
Power tool use
ENGLISH 26
Rotating direction of the cut-off wheel in the installed condition: Î Chap. 5.1, page 16
Abrasive resin cut-off wheels must not be exposed to moisture. The water connection for wet cutting must
not be used when using abrasive resin cut-off wheels. Abrasive resin cut-off wheels must not be used in
high humidity or in rain. Only use abrasive resin cut-off wheels until the end of the best-before date
imprinted on the receptacle ring of the cut-off wheel.
The power tool's spindle is designed for cut-off wheels with an inner bore of 20 mm.
Cut-off wheels with a 1" inner bore must only be installed with the spindle adapter disk supplied with the
power tool.
Installation of cut-off wheels with 1" inner bore: Î Chap. 5.2, page 17
Cut-off wheels with other inner bores must not be installed! Never modify the bore of the cut-off wheel!
New cut-off wheels must be tested for at least 60 seconds at the indicated maximum speed before the first
cutting process. No body parts must be located in the extended swivel range of the cut-off wheel.
8
The upper part of the cut-off wheel must
not be used for cutting!
9
Only the lower part of the cut-off wheel
must be used for cutting!
Danger of injury from kickback!
Kickback results when the upper part of the cut-off wheel is used for cutting.
The power tool is pushed towards the user's head uncontrolledly and at high speed.
x Never cut with the upper area of the cut-off wheel!
x Take special care at insertion into cutting areas already started!
Danger of injury from pinching!
Pinching results when the cutting point becomes more narrow (crack or tensioned work piece).
The power tool is accelerated forwards uncontrolledly and under high energy.
x Always perform cutting and repeated insertion into cutting points already started at the maximum speed.
x Always support the work piece so that the cutting point is under tension so that the cut-off wheel is not
clamped when cutting any further.
x When starting cutting, carefully move the cut-off wheel to the work piece; do not apply it suddenly.
x Never cut several work pieces at once!
x Ensure that no other work piece is touched when cutting.
7.2 Permissible cutting area and danger from kickback or pinching
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 879 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 879 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info