619690

Snooper S3 Manual

11
Zoom out
Zoom in
Previous page
1/14
Next page
10
Installing your Snooper S3 using the Windscreen Suction Cup
bracket
If you prefer you can mount your S3 to the inside of your vehicles
windscreen using the suction cup bracket provided. Simply select a
position within the windscreen so that the top of the unit has a clear view
of the sky, remembering that you need to connect both the power and
RLD (If required) connection cables as well as ensuring that you can read
the LED display and reach the controls safely. Follow these instructions
to mount the unit in this way.
- Install the suction cups onto the bracket by fitting them into it’s holes.
- Clean the area where you wish to position the bracket thoroughly with a
good quality glass cleaner.
- Carefully bend the bracket so that when it is mounted on to the
windscreen with the S3 attached, the Control Panel is facing in the
desired direction so that you can easily see the LED display and
safely operate the controls.
- Slide the S3 onto the bracket until it is secure and the unit is positioned
in as horizontal a position as possible.
-To remove the S3 simply slide the unit off the bracket from the front.
- Finally plug the smaller plug on one end of the power cable into the
socket marked DC12V on the back off the S3 and plug the larger plug
into the cigarette lighter socket of your vehicle. Your Snooper S3 is now
ready for use. For further information please read the section on Power
Connection on page 11.
RS232
RD
17
Operating Instructions
1. Starting Up
After you have successfully installed your S3 and performed the download
it is time to perform the first start up. Firstly make sure your vehicle is
parked in as open a space as possible, clear of tall trees and buildings so
that the built-in GPS antenna has a clear view of the sky above. Next
power the unit up by turning the on/off/volume towards you. The S3 will
go through a brief self test procedure and then a red LED will scan back
and forth across the display indicating that the unit is searching for
satellite connection. The S3 needs to acquire a minimum of 3 satellites to
work effectively, once this has been achieved the S3 will proceed to the
standby screen with just the green letter ’P’ illuminated. As soon as the
standby screen is being displayed your S3 is ready for use and will now
automatically alert you of any locations stored in it’s database as well as
laser alerts and radar alerts if you have a S100-RLD connected.
As the GPS engine and antenna have never been used before, the first
’Cold’ start up could take somewhere between 5 - 30mins. Once
initialised, subsequent start ups will take as little as 3 mins.
2. Cancel Button
If during an alert you decide that you would like to cancel it, simply press
and hold the ’Cancel’ button. The display will automatically return to the
Standby screen and the device will be ready to alert you the next time
you encounter a stored co-ordinate or laser source.
3. Mute Button
If during an alert you decide that you would like to mute it, simply press
the ’Mute’ button briefly. The screen will continue to display a visual alert
but no sound will be heard. After you have travelled out of range of the
location the device will automatically reset so that next time you
encounter a location you will receive both audible and visual alerts as
normal.
CANCEL
NEW LOCATION
MUTE
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snooper S3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snooper S3 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info