619690
12
Zoom out
Zoom in
Previous page
1/14
Next page
11
Power Connection
Using the cigarette lighter socket
The S3 comes with a power cable designed to plug into your vehicles
cigarette lighter socket. Take the lead and plug the smaller end into the
DC 12v input socket on the back of the S3 and the cigarette lighter
adaptor in your vehicles cigarette lighter socket.
Please Note: Do not leave your S3 plugged into the cigarette lighter
socket when you start your vehicle. The cigarette lighter socket is prone
to power surges when the vehicle is started that may damage your unit.
If the device does not power up please check that the cigarette lighter
socket is clean of any debris, remembering not to insert any metal objects
into the socket, check that the cigarette lighter adaptor is inserted all the
way into the socket and to check that the fuse in the cigarette lighter
adaptor is operational. If your S3 will still not power up, please check that
the cigarette lighter in your vehicle is functioning correctly.
Replacing the Fuse
If the detector stops operating, the fuse in the cigarette lighter plug might
be blown. If it has blown, follow these steps to replace it with a 2 amp, 5 x
20mm, fast acting fuse.
Caution: Using a fuse that does not meet these ratings or defeating fuse
protection can damage your detector, the power cable, or the vehicles
electrical system.
1. Grasp the ring near the tip of the cigarette lighter plug, then carefully
unscrew the ring by turning it counterclockwise.
16
- Next use a damp cloth to thoroughly clean the bottom of the S100-RLD
and the side of the bracket where you intend to mount the device.
- Peel the backing paper from one side of the double-sided tape and
apply it to the bottom of the unit.
- Next remove the backing paper from the
other side of the tape and position the
S100-RLD onto the ’L’ shaped bracket as
indicated in the diagram below ensuring
that the front of the detector is facing
forwards down the road. Please note
it will take approximately 24hrs for the
double sided tape to adhere properly to the
bracket and unit.
- Feed the cable from the S100-RLD through
an existing grommet in the bulkhead to
the cockpit of the vehicle and plug the
end of the cable into the socket on the
side of the S3 marked ’RD’. If there
is not a convenient grommet to
use you will need to drill an
additional hole sealed with a
grommet, large enough to feed
the cable and plug through.
Ensure that the cable running
from the S100-RLD to the
S3 is secured periodically
so that it does not interfere with
any of the workings of the vehicle.
Mounting Notes
When mounting the S100-RLD always ensure that you mount the unit
away from any moving parts such as air cooling fans or the fan belt.
Always position the unit so that you can safely feed the cable back
through to the cockpit of the vehicle without the cable interfering with any
moving parts within the engine bay or interfering with any part of the
vehicle that could endanger you or your passengers. Please check that
all surfaces are safe to drill through before beginning any work.
IMPORTANT
If you are unfamiliar with any of the above procedures, please
consult a professional auto electrician.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snooper S3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snooper S3 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info