619670
10
Zoom out
Zoom in
Previous page
1/22
Next page
10
Return to contents
Charging the internal battery
Lynx can be charged using either the cigarette lighter adaptor in your vehicle or via the mains adaptor. If the unit is turned on the
battery charge icon will be animated during charging.
Once fully charged the battery will last approximately 3 hrs during normal use.
Note: The new batterys full performance is only achieved after two or three complete charges and discharges.
Direct connecting/hard wiring Lynx
You can power Lynx by wiring it directly to your vehicles 12V electrical system using the ‘Hard Wire cable which is supplied as
standard with your unit. First connect the positive side of the cable (marked with a red plus symbol) to a 12V switched live. This is
a live that is ON when the ignition is ON and OFF when the ignition is OFF. The negative side of the lead should be connected to a
negative ground, so it can be attached to any metal portion of the vehicles frame. Next plug the small adaptor on the other end of
the lead into the 12V DC input socket on the left side of the unit.
Important: If you are unfamiliar with this procedure, please consult a professional auto electrician.
Operating Instructions
1. Using Lynx for the first time
Firstly Lynx will need to establish a connection to the GPRS network. The time taken can vary, please refer to page 6. After you
have installed Lynx into your vehicle it is time to perform the rst start up. First make sure your vehicle is parked in as open a space
as possible, clear of tall trees and buildings so that Lynx has clear a view of the sky above. Next switch the unit on by pressing
the Standby Power button for two seconds. The LCD graphical display will briey display the ‘Lynx’ logo, Logic # (see Section 11),
Mway, City or All (see Section 7) and nally ’Searching for Satellites will ash on the screen as the unit begins to search for satellite
connection.
Lynx needs to acquire a minimum of four satellites in order to work. Once this has been achieved Lynx will proceed to the Standby
screen of your choice (See Standby Screen below). As soon as the standby screen is displayed Lynx is ready to use and will now
automatically alert you of any locations stored in its database. A variety of audible and visual alert patterns are available. See ‘Features
and Settings’ later in this user manual for more detailed information.
As the GPS engine and antenna have never been used before, the first ‘Cold’ start could take anywhere from 15 – 50 minutes to
establish a satellite connection. Once initialised, subsequent start ups will take less time and eventually should take only a matter
of minutes.
Please Note: If the unit is not used for some time the initial GPS start up may take longer than when the unit is used regularly.
2. Standby Screen
There are eleven dierent screen colour settings for the standby display. To change the
screen colour:
Press the ‘MENU’ button to enter the menu – the ‘Set Alert Range menu option will be
displayed.
Push the ‘UP button until ‘Change Screen Colour’ is displayed and then press the ‘OK’
button.
Ptress the ‘UP and ‘DOWN’ buttons to scroll through the screen colour options. When your preferred setting is displayed, press the
‘OK’ button again. The unit will conrm the new setting has been stored.
If you would like to exit the Menu at any time press either the Target’ or the ‘MENU button. If no buttons are pressed for a period of
ve seconds the unit will automatically exit the Menu and return to your chosen standby display.
Change Screen Colour
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snooper Lynx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snooper Lynx in the language / languages: English as an attachment in your email.

The manual is 2,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info