621561
65
Zoom out
Zoom in
Previous page
1/84
Next page
65
v1.06
Admin and Installation Guide M700, M300 Description of Settings
Network
Setting Description
IP settings
DHCP/Static IP Allowing changes in protocol for getting a dynamic IP address. When DHCP is
enabled, the other IP settings and options are not available.
DHCP enabled: IP addresses are allocated from a pool of available addresses.
Static IP: IP addresses are manually assigned by the network administrator.
Default: DHCP.
IP address Enter when using static IP address. Not accessible when using DHCP.
Subnet mask Enter when using static IP address. Not accessible when using DHCP.
Default gateway Enter IP address of your router when using static IP address. Not accessible
when using DHCP.
DNS (Primary) Enter DNS server address of Internet service provider when using static IP
address. Not accessible when using DHCP.
DNS (Secondary)
VLAN Settings The VLAN settings can be used on a managed network with separate Virtual
LANs (VLAN) for sending voice and data trac. To work on these networks,
the base station can tag voice trac it generates on a specic "voice VLAN"
using the IEEE 802.1q specication.
ID 12-bit identication of the 802.1Q VLAN. Permitted value(s): Decimals 0 to
4094. A VLAN ID of 0 is used to identify priority frames and the ID of 4095
(i.e., FFF) is reserved. If 0 is set, there is no VLAN tagging or VLAN discovery
through DHCP.
Default: 0.
User priority 3-bit value dening user priority. Values are 0 (best eort) and 1 to 7 (lowest
to highest priority). The values can be used to prioritize dierent classes of
trac (voice, video, data, etc.).
Default: 0
Synchronization If enabled, the VLAN ID is automatically synchronized between the base
stations in a multicell chain. They will be automatically rebooted during the
synchronization.
Default: Disabled.
DHCP Options
Plug-n-play If enabled: DHCP option 66 is used to automatically provide PBX IP address to
base station.
Default: Disabled.
NAT Settings
Enable STUN Default: Disabled. Enable to use STUN.
STUN server Permitted value(s): IPv4 values or URL. Currently only IPv4 is supported.
STUN bindtime determine Default: Disabled.
STUN bindtime guard Time in seconds. Permitted values: Positive integers.
Default: 80.
Enable RPORT Default: Disabled. Enable to use RPORT in SIP messages.
Keep alive time The interval in seconds at which the base station sends a keepalive signal to
the SIP server to maintain NAT bindings. Permitted values: Positive integers.
Default: 90.
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Snom M300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Snom M300 in the language / languages: English as an attachment in your email.

The manual is 2.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Snom M300

Snom M300 User Manual - English - 44 pages

Snom M300 User Manual - English - 38 pages

Snom M300 User Manual - English - 58 pages

Snom M300 User Manual - German - 82 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info