785804
12
Zoom out
Zoom in
Previous page
1/37
Next page
89
2.4 Setting the control unit
If desired or necessary, the position of the display [12] can be adjusted.
Switch off the drive unit completely (see chapter 3.6.2).
Open the cover [13] of the control unit.
Loosen the three screws [26] on the back of the control unit by not more than half
a turn. To this end, use an Allen key, size 2.5.
Turn the ring [25] until the display [12] is in the desired position. Then carefully
tighten the three screws [26] until the ring [25] can no longer be turned.
Close the cover [13] of the control unit.
3. Drive mode
3.1 Switching on the system
The drive and control unit need to be switched on for use be possible. Carry out the fol-
lowing steps to this end:
Switch off all Bluetooth devices in your immediate vicinity to prevent any interference
with the connection between the drive unit and control unit.
Ensure that the drive wheel [8] is correctly aligned with the drive unit (see chapter 3.4).
Briefly press the button [3] on the drive unit. This switches on the drive unit. A brief
acoustic signal sounds, the button [3] lights up green, and the display [2] indicates
the capacity of the battery. (see chapter 5.1). The position light [7] now lights up as
well.
Switch on the control unit (this needs to be in the mount [16]) by pressing the but-
ton [10] on it for approx. 2 seconds.
The LED [f] now indicates the capacity of the control unit battery in different colours
(see chapter 5.2). If the LED [f] is flashing blue, this indicates an attempt to establish
a connection to the drive unit via Bluetooth.
If no Bluetooth connection is established within 10 seconds, the LED [f] flashes red
for 20 seconds. The control unit then switches off.
If the Bluetooth connection is established between the drive unit and the control
unit, the LED [f] on the control unit lights up continuously. See chapter 5.2. for the
meaning of colour. The capacity of the drive unit battery is also displayed.
If no Bluetooth connection is established after you have performed the steps listed
above, this may be due to the following reasons:
Incorrect alignment of the drive wheel
If the drive wheel [8] is in an incorrect position (see chapter 3.4), the drive unit cannot
be switched on. Instead, the On/Off button [3] lights up green and the LED [c] in the
display [2] flashes white.
Drive unit battery is empty
If the battery no longer has sufficient capacity, the LED [a] flashes briefly in the display
[2] when the SMOOV O10 is switched on. The system switches off completely thereafter.
Charge the battery as described in chapter 4.1.
The control unit battery is empty
If the battery no longer has sufficient capacity, the LED [f] flashes briefly in the display
[12] when the control unit is switched on. The system switches off completely thereafter.
Charge the battery as described in chapter 4.2.
Error in the system
In this regard, see the explanations in chapter 6.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smoov One O10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smoov One O10 in the language / languages: English as an attachment in your email.

The manual is 4.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smoov One O10

Smoov One O10 User Manual - German - 36 pages

Smoov One O10 User Manual - Dutch - 36 pages

Smoov One O10 User Manual - French - 36 pages

Smoov One O10 User Manual - Italian - 36 pages

Smoov One O10 User Manual - Spanish - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info