590662
23
Zoom out
Zoom in
Previous page
1/26
Next page
23
3. Mount the Detector to the fixed part of the frame along the opening edge opposite the hinges using
either the double sided adhesive tape or screws provided.
If fixing the Detector with screws; fit the Keyhole slot in the top of the Detector over the head of the
smaller pan-head screw. Secure the bottom of the Detector using the 12mm countersunk head screw
fitted within the battery compartment. You will need to drill out the centre of the fixing screw hole using
a 3mm drill. Do not over tighten the fixing screws as this may distort or damage the casing.
4. Fit the Magnet to the moving part of the door/window opposite the Detector using the adhesive tape
or 15mm fixing screws.
Ensure that the parallel gap between the Magnet and Detector is less than 10mm and that the arrow
on the Magnet is pointing towards and aligned with the mark on the Detector.
5. If several windows need to be protected, remove the self-contained wired supplied and adopt the wire
according to the specifications as mentioned below. This should be wired to the terminal block
provided in the battery compartment in series connection. The wired contact should be connected
using two core (24AWG) wire of maximum length 1.5m.
A cable entry cut-out is available and adjacent to the terminal block.
6. Refit the battery cover.
SETTING THE MAGNETIC CONTACT DETECTORS
1. Located on the PCB of the Detector is a two-position DIP
switch (SW2).
2. DIP switches 1-2 are used to enable/disable the internal or
external wired magnetic contact. If setting the DIP1 & DIP2 to
‘Off’, only the internal contact will be active. When two
contacts are in use for internal and external connection
simultaneously, one activation will be counted if one of the
contacts is opened; while both contacts must be
all close, the Detector will then be treated as
close.
3. If external contacts are wired to the Detector, set
the DIP1 to ‘Off’ and DIP2 to ‘On’.
IMPORTANT: If external contacts are not
connected, set the DIP1 to ‘On’ and DIP2 to ‘Off
for the detector to operate correctly.
4. In order to communicate with the Control Panel,
the ID code of the Detector needs to be learned by
the Control Panel. By pressing the tamper switch
either located adjacent to the PCB or rear cover of
the Detector will emit the ID code to the
Control Panel instantly, subject to the Control Panel being set at the Zone setup mode.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smartwares HA700 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smartwares HA700 plus in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smartwares HA700 plus

Smartwares HA700 plus User Manual - Dutch - 26 pages

Smartwares HA700 plus User Manual - Dutch, French - 52 pages

Smartwares HA700 plus Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info