590662
22
Zoom out
Zoom in
Previous page
1/26
Next page
22
Note: On initial installation the detector should be set into Walk Test mode ready for testing. Upon
completion of Walk Test mode, set DIP1 of SW2 to OFF for normal detection mode.
2. The PIR Detector incorporates an anti-false alarm feature designed to compensate for situations
where the detector may be affected by environmental changes, (e.g. insects, air temperature, etc).
This feature is called “sensitivity detection” and may be selected for high or low detection.
The recommended setting is for high sensitivity detection. However, in cases of extreme
environmental problems or if unattributable false alarms are experienced, it may be necessary to
select low sensitivity detection.
Set the required sensitivity detection using DIP2 of SW2 as follows:
ON high sensitivity detection
OFF low sensitivity detection
Note: The higher the sensitivity detection the less movement will be necessary before the PIR detector
will trigger the alarm.
6.3 Door/window (magnetic) opening detector SA68M
The Magnetic contact consists of two parts; a Detector and a Magnet. They are designed to be fitted to
doors or windows with the Magnet mounted on the opening part and the Detector mounted on the fixed
frame. Opening the protected door/window will remove the magnetic field, trigger the Detector and
generate an alarm condition, (if the system is armed and the alarm zone active).
The Detector is powered by one 3.6V 1200mAh Lithium battery which under normal conditions will have
typical life in excess of 5 years. Under normal battery conditions with battery cover fitted the LED on the
Detector will not illuminate when the Detector is triggered, (unless in test mode). However, under low
battery conditions this LED will be illuminated when the detector is triggered. When this occurs the battery
should be replaced as soon as possible.
For double security, there are two tamper switches fitted on the Detector. (FIGURE 2) Either removing the
Detector from the protected door/window or removing the battery cover will generate a full alarm condition.
The Magnetic Contact Detector is of self-contained wired Magnetic Contact. This contact must be of a
normally closed contact type with the contacts being opened in order to generate an alarm condition.
CHOOSING A MOUNTING LOCATION
The Magnetic Contact Detector is suitable for mounting in dry interior locations only. Decide which
doors/windows are to be protected by Magnetic Contact Detectors, (usually the front and back doors as a
minimum will have Magnetic Contact Detectors fitted). Additional detectors may also be fitted where
required to other vulnerable doors or windows, (e.g. garage, patio/conservatory doors etc).
Note: Take care when fixing the Detector to a metal frame, or mounting within 1m of metalwork (i.e.
radiators, water pipes, etc) as this could affect the radio range of the device. If required, it may be
necessary to space the magnet and detector away from the metal surface using a plastic or wooden
spacer to achieve the necessary radio range.
INSTALLING THE MAGNETIC CONTACT DETECTORS
Ensure that the system is in Test Mode.
1. Undo and remove the fixing screw from the bottom edge of
the Detector. Remove the battery cover by sliding and lifting it
off. (DO NOT use a screwdriver to lever the cover off).
2. Fit the 3.6V Lithium battery supplied, with the negative (-)
towards the battery spring.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smartwares HA700 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smartwares HA700 plus in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smartwares HA700 plus

Smartwares HA700 plus User Manual - Dutch - 26 pages

Smartwares HA700 plus User Manual - Dutch, French - 52 pages

Smartwares HA700 plus Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info