590662
21
Zoom out
Zoom in
Previous page
1/26
Next page
21
INSTALLING THE PIR DETECTORS
(Ensure that the system is in Test Mode).
1. Undo and remove the fixing screw from the bottom edge of the
PIR. Carefully pull the bottom edge of the detector away from
the rear cover and then slide down to release the top clips
2. Carefully drill out the required mountingholes in the rear cover
using 3mm drill according to whether the unit is being mounted
in a corner or against a flat wall.
Note: Using 1st mounting hole to fulfill corner mounting installation,
while 2nd mounting hole for flat wall installation.
3. Using the rear cover as a template, mark the positions of the
fixing holes on the wall.
4. Fix the rear cover to the wall using the two 18mm No.4 screws
and 25mm wall plugs, (a 5mm hole will be required for the wall
plugs). Do not over-tighten the fixing screws as this may distort
or damage the cover.
5. Configure the PIR detector as described below. Remember that
on initial installation that the device needs to be tested and
should therefore be set in Walk Test Mode.
6. Check that the detector PCB is located and set in the correct
position to provide the required detection range. To adjust the
PCB position, simply slide it up or down ensuring that the
location legs are aligned with the required position number
marked on the board.
7. To refit the PIR detector to the rear cover and locate the clips in
the top edge into the rear cover. Push the lower edge of the
detector into place and refit the fixing screw in the bottom
edgeof the PIR to secure in position. Do not over-tighten the
fixing screws as this may damage the casing.
SETTING THE PIR DETECTORS
Located on the PCB of the PIR Detector is a two-position DIP switch (SW2). When conducting the Walk
Test, ensure that the DIP switch SW2 is set as follows:
1. DIP1 of SW2 is used to configure the PIR Detector for walk test mode, which allows the operation of
the detector to be checked during installation without triggering a Full Alarm.
ON Walk Test mode
OFF Normal mode
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smartwares HA700 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smartwares HA700 plus in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smartwares HA700 plus

Smartwares HA700 plus User Manual - Dutch - 26 pages

Smartwares HA700 plus User Manual - Dutch, French - 52 pages

Smartwares HA700 plus Additional guide - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info