758596
8
Zoom out
Zoom in
Previous page
1/160
Next page
8
OUTDOOR USE
• Connectthetoolviaafaultcurrent(FI)circuitbreaker
withatriggeringcurrentof30mAmaximum
BEFORE USE
• Beforeusingthetoolforthersttime,itis
recommendedtoreceivepracticalinformation
• Alwayscheckthatthesupplyvoltageisthesameasthe
voltageindicatedonthenameplateofthetool(tools
witharatingof230Vor240Vcanalsobeconnectedto
a 220V supply)
• AlwaysmountauxiliaryhandleE2andprotective
guard F 2;neverusethetoolwithoutthem
• Usesuitabledetectorstofindhiddenutilitylinesor
callthelocalutilitycompanyforassistance (contact
withelectriclinescanleadtoreorelectricalshock;
damagingagaslinecanresultinanexplosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Donotworkmaterialscontainingasbestos (asbestos
is considered carcinogenic)
• Dustfrommaterialsuchaspaintcontaininglead,some
woodspecies,mineralsandmetalmaybeharmful
(contactwithorinhalationofthedustmaycause
allergic reactions and/or respiratory diseases to the
operatororbystanders);wearadustmaskandwork
withadustextractiondevicewhenconnectable
• Certainkindsofdustareclassiedascarcinogenic(such
as oak and beech dust) especially in conjunction with
additivesforwoodconditioning;wearadustmaskand
workwithadustextractiondevicewhenconnectable
• Followthedust-relatednationalrequirementsforthe
materials you want to work with
• Becarefulwhencuttinggrooves,especiallyin
supporting walls (slots in supporting walls are subject to
country-specicregulations;theseregulationsaretobe
observedunderallcircumstances)
• Securetheworkpiece (a workpiece clamped with
clampingdevicesorinaviceisheldmoresecurelythan
by hand)
• Donotclampthetoolinavice
• Usecompletelyunrolledandsafeextensioncordswith
acapacityof16Amps(U.K.13Amps)
DURING USE
• Inrushcurrentscauseshort-timevoltagedrops;under
unfavourablepowersupplyconditions,otherequipment
maybeaffected(ifthesystemimpedanceofthepower
supplyislowerthan0,25Ohm,disturbancesare
unlikelytooccur);ifyouneedfurtherclarication,you
may contact your local power supply authority
• Ifthecordisdamagedorcutthroughwhileworking,do
nottouchthecord,butimmediatelydisconnecttheplug
• Neverusethetoolwhencordisdamaged;haveit
replacedbyaqualiedperson
• Incaseofelectricalormechanicalmalfunction,
immediatelyswitchoffthetoolanddisconnecttheplug
• Incaseofcurrentinterruptionorwhentheplugis
accidentallypulledout,unlocktheon/offswitchH2
immediatelyinordertopreventuncontrolledrestarting
AFTER USE
• Afterswitchingoffthetool,neverstoptherotationof
theaccessorybyalateralforceappliedagainstit
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Donotconnecttheblue(=neutral)orbrown(=live)wire
inthecordofthistooltotheearthterminaloftheplug
• Ifforanyreasontheoldplugiscutoffthecordofthis
tool,itmustbedisposedofsafelyandnotleftunattended
USE
• Mountingofaccessories2
! disconnecttheplug
- clean spindle A and all parts to be mounted
- tighten clamping flange B with spanner C while
pushing spindle-lock button D
! pushspindle-lockbuttonDonlywhenspindleAis
atastandstill
- forremovingaccessorieshandlevice-versa
! grinding/cuttingdiscsbecomeveryhotduringuse;
donottouchthemuntiltheyhavecooleddown
! alwaysmountbackingpadwhenusingsanding
accessories
! neveruseagrinding/cuttingdiscwithoutthelabel
(“blotter”)whichisgluedontoit(ifprovided)
• MountingofauxiliaryhandleE5
! disconnecttheplug
- screwauxiliaryhandleEontheright,thetop,ortheleft
ofthetool(dependingontheworktobecarriedout)
• Removing/mounting/adjustingofprotectiveguardF6
! disconnecttheplug
! ensurethattheclosedsideoftheprotective
guardalwayspointstotheoperator
- ifnecessary,adjustprotectiveguardFbytightening
screwXwhichispre-setatmanufacturing(ensure
thattheprotectiveguardisclosed)
• Beforeusingthetool
- ensure that accessory is correctly mounted and firmly
tightened
- checkifaccessoryrunsfreelybyturningitbyhand
- test-runtoolforatleast30secondsathighest
no-loadspeedinasafeposition
- stopimmediatelyincaseofconsiderablevibrationor
otherdefectsandchecktooltodeterminethecause
• On/offlockingswitchH7
- switch on tool 7a
! beawareofthesuddenimpactwhenthetoolis
switchedon
! beforetheaccessoryreachestheworkpiece,the
toolshouldrunatfullspeed
- lock switch 7b
- unlockswitch/switchofftool7c
! beforeswitchingoffthetool,youshouldliftit
fromtheworkpiece
! theaccessorycontinuestorotateforashorttime
afterthetoolhasbeenswitchedoff
• Grinding8
- movethetoolbackandforthwithmoderatepressure
! neveruseacuttingdiscforsidegrinding
• Cutting9
- do not tilt the tool while cutting
- alwaysmovethetoolinsamedirectionasarrowon
toolhead,inordertopreventthetoolfrombeing
pushedoutofthecutinanuncontrolledmanner
- donotapplypressureonthetool;letthespeedof
the cutting disc do the work
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 9425 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 9425 in the language / languages: All languages as an attachment in your email.

The manual is 3,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info