Manual Skil 0770 (page 8 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

480089

Zoom out

Zoom in

1/96

• Only operate the tool in open space (not too close to a

wall or other solid objects) and on a rm, level surface

• Store the tool indoors in a dry and locked-up place, out

of reach of children

BEFORE USE

• Check that all screws, nuts, bolts and other fasteners are

properly secured and that guards and screens are in place

• Ensure that the feed intake is empty

DURING USE

• Keep your face and body away from the feed

intake opening

• Do not allow hands (or any other part of the body) or

clothing inside the feed intake opening, outlet opening or

near any moving part

• Keep proper balance and footing at all times; do

not overreach

• Never stand at a higher level than the base of the tool

when feeding material

• Always keep proper distance from the outlet zone when

operating the tool

• When feeding material into the tool be extremely careful

that pieces of metal, rocks, bottles, cans or other foreign

objects are not included

• If the cutting mechanism strikes any foreign object or if

the tool should start making any unusual noise or

vibration, immediately switch o, allow the cutting blade

to stop, disconnect the plug and take the following steps

- inspect for damage

- replace or repair any damaged parts

- check for and tighten any loose parts

• Do not allow processed material to build up in the outlet

zone; this may prevent proper discharge which can result

in kickback of material through the feed intake opening

• If the tool becomes clogged, switch o, allow the cutting

blade to stop and disconnect the plug before

clearing debris

• Keep the motor cooling vents clean of debris and other

accumulations to prevent damage to the motor or

possible re

• Do not tilt or transport the tool while the motor is running

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Assembly instructions $

- mount wheels with the two wrenches A supplied and

assemble tool as illustrated

- position collection bag B underneath outlet C

- mount prodder holder D

• On/o %

- switch on/o the tool by pushing switch E in

“I”/”O” position

! after switching off the tool the blade continues to

rotate for a few seconds

- allow the cutting blade to stop rotating before

switching on again

! the tool will not start unless securing knob F is

fully tightened

! do not rapidly switch on and off

• Restart protection

- after a power supply failure the tool will not restart on

its own

- use switch E % for restarting the tool

• Overload protection

Overloading (e.g. blocking up the cutting blade) can lead

to a standstill of the tool

- wait a short period before switching on the tool again

- restart tool by rst pushing button G % and then

switch E %

• Shredding ^

- feed the material to be chopped through feed intake

opening H

- only insert as much material so that the feed intake will

not be blocked up

! longer material could lash out when being cut

! small pieces of shredded material may be ejected

from the feed intake opening

! wear safety glasses, hearing protection and

protective gloves when using the tool

- do not ll soft waste such as kitchen rubbish into

the shredder

- ensure that the chopped material can fall freely from

outlet C

- ensure that ventilation slots J 2 will not be covered by

the collection bag or the chopped material

- avoid blocking outlet C with shredded material as this

could result in kickback of material through feed intake

opening H

• Removing blockage &

! switch off the tool and disconnect the plug

- loosen securing knob F and open the tool as illustrated

- clean the blade area (remove compacted debris with a

woorden or plastic implement)

- also clean outlet C of any debris

- close the tool and tighten securing knob F rmly

• Reversing/changing cutting blade *

! switch off the tool and disconnect the plug

- the cutting blade has a cutting edge on both sides; so

if one side has become blunt, the other side can

be used

- replace the cutting blade when both sides are blunt

(SKIL spare part number 2610Z02553,

marked YAT 8231-545201)

- loosen securing knob F and open the tool as illustrated

- loosen both blade bolts with hex key L while using

metal plate M as support

- reverse and mount the cutting blade as illustrated

- tighten both blade bolts with hex key L while using

metal plate M as support

- close the tool and tighten securing knob F rmly

APPLICATION ADVICE

• For best results shred fresh branches soon after they

have been cut

• Use prodder K for feeding soft material (

• Shred soft garden waste in smaller loads, particularly

when wet

• Blockages can be avoid by intermittently

shredding branches

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0770 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 0770 Manual

Product: