480089
7
Zoom out
Zoom in
Previous page
1/96
Next page
7

Shredder 0770
INTRODUCTION
This tool is not intended for professional use
This tool is intended for cutting brous and woody garden
waste for composting
Check whether the packaging contains all parts as
illustrated in drawing 2
When parts are missing or damaged, please contact
your dealer
Read this instruction manual carefully before use and
save it for future reference 3
Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious injury
TECHNICAL SPECIFICATIONS 1
) The S6 operating mode (P40 = 40%) indicates a load
prole of 4 min load and 6 min idle time (for practical
application, continuous operation is permitted)
TOOL ELEMENTS 2
A Wrench (2)
B Collection bag
C Outlet
D Prodder holder
E On/o switch
F Securing knob
G Button for restarting
H Feed intake opening
J Ventilation slots
K Prodder
L Hex key
M Metal plate
N Safety lock
SAFETY
SPECIFIC SAFETY INSTRUCTIONS FOR SHREDDERS
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Switch off and disconnect plug before cleaning/
maintenance or if (extension) cord is damaged
or entangled
5 DANGER Rotating blades; keep hands out of openings
while tool is running
6 Pay attention to the risk of injury caused by flying
debris (keep bystanders a safe distance away from
work area)
7 Wait until all moving tool components have come to a
complete standstill before touching them
8 Wear protective gloves
9 Wear protective glasses and hearing protection
0 Do not expose tool to rain
! Double insulation (no earth wire required)
@ Do not dispose of the tool together with household
waste material
# Plugs and sockets situated near the work site or outdoors
should be class IP X4 of BS 5490 to provide adequate
protection against ingress of water, etc. and cable entries
require eective sealing
GENERAL
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety
Ensure that children do not play with the tool
Be familiar with the controls and the proper use of the tool
Never allow children or people who are not familiar with
the operating instructions to use the tool (local
regulations can restrict the age of the operator)
Never operate the tool in the direct vicinity of persons;
stop using the tool while persons (especially children) or
pets are nearby
The user is responsible for accidents or hazards
occurring to other people or their property
Keep all guards and deectors in place and in good
working condition
Always switch o the tool, allow the cutting blade to stop
and disconnect the plug
- whenever leaving the tool unattended
- before clearing jammed material
- before checking, cleaning or working on the tool
! before mounting or removing the collection bag
ELECTRICAL SAFETY
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Inspect the cord periodically and have it replaced by a
qualied person, if damaged
Inspect the extension cord periodically and replace it, if
damaged (inadequate extension cords can be
dangerous)
When operating the tool use a residual current device
(RCD) with a triggering current of 30 mA maximum
Only use an extension cord of types H05VV-F or
H05RN-F which is intended for outdoor use and
equipped with a watertight plug and coupling-socket
Always switch o tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
A damaged power cord shall be replaced at a SKIL
service centre only in order to avoid a hazard
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
Protect the (extension) cord from heat, oil and
sharp edges
Do not run over, crush or pull the (extension) cord
Only use extension cords with a maximum length of 20
metres (1,5 mm²) or 50 metres (2,5 mm²)
PERSONAL SAFETY
Do not operate the tool when barefoot or wearing open
sandals; always wear sturdy shoes and long trousers
Avoid wearing loose-tting clothing that is loose-tting,
hanging cords or ties
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0770 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0770 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info