797781
14
Zoom out
Zoom in
Previous page
1/164
Next page
14
-press and rotate in the direction of the arrow P until
approx. 13 cm of line is left on both sides
Remove line o
In case the cutting line fails to protrude from spool hole
! 
-press release buttons N to remove the spool cover
-remove the line from the spool
-align and press the spool cover until it snaps into place
-follow “Line replacement” instruction above
MAINTENANCE / SERVICE
This tool is not intended for professional use

ensure that all moving parts have come to a complete
standstill
Always keep tool clean (especially ventilation slots A 2)
-clean the tool with a damp cloth (do not use cleaning
agents or solvents)
-clean line cutting blade Q 2 and cutting guard G 2
after each use
-clean ventilation slots A 2 regularly with a brush or
compressed air
Regularly check the condition of the cutting head and the
tightness of nuts, bolts and screws
Regularly check for worn or damaged components and
have them repaired/replaced when necessary
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the product will be excluded from the
warranty (for the SKIL warranty conditions see
www.skil.com or ask your dealer)
TROUBLESHOOTING
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! in case of electrical or mechanical malfunction,

Tool does not operate
-empty battery -> charge battery
-hot battery -> let battery cool down
-internal fault -> contact dealer/service station
Tool operates intermittently
-internal wiring defective -> contact dealer/service
station
-
Tool vibrates abnormally
-grass too high -> cut in stages
Tool does not cut
-
Line cannot be fed
-spool empty -> inspect spool; rewind if necessary
-line entangled inside spool -> inspect spool; rewind if
necessary

cutting blade
being switched on, when
-remove load and restart
-the 4 levels of the battery level

from the tool and charge the battery qc
-the battery temperature is not within the allowable

4 levels of the battery level indicator keep solid red for
10s; wait until battery has returned within the allowable
operating temperature range qd
! 

damaged
Trimming
! ensure that the cutting area is free of stones,
debris and other foreign objects
! start trimming only when tool runs at full speed
-cut long grass in layers (always start from the top)
-only trim with the tip of the cutting line
-do not cut damp or wet grass
-prevent the cut grass from clogging the spool (do not
make heavy cuts)
-do not overload the tool
-carefully cut around trees and bushes, so that they do
not come into contact with the cutting line
-keep the tool away from solid objects in order to protect
the cutting line against excessive wear
-be aware of the kickback forces that occur when solid
objects are touched
Holding and guiding the tool y
-for cutting long grass slowly swing the tool from right to
left and vice versa
-
control of the tool at all times
-maintain a stable working position
-always hold the tool well away from your body
Line feeding u
-tap trimmer head lightly on a solid surface while the
motor is running
! tap trimmer head on bare ground or hard soil,
when tapping in tall grass, the motor may overheat
-
length by line cutting blade Q
! take care against injury from line cutting blade Q
-feed the lines regularly to maintain full cutting circle
-when the motor runs without load and no grass is cut,
the cutting line is stuck, worn or broken; rewind or
replace the line

-
-press the trimmer head and pull the lines to feed the
line manually and check for proper installation
-after line feeding always return the tool to its normal
operating position before switching on
-when the motor runs without load and no grass is cut,
the cutting line is stuck, worn or broken; rewind or
replace the line
Line replacement i
! 
-insert the 5m long cutting line into spool hole and push
until it protrudes from the other side
-pull the line until equal amounts of line appear on both
sides
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 0280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 0280 in the language / languages: All languages as an attachment in your email.

The manual is 7.31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info