459425
22
Zoom out
Zoom in
Previous page
1/40
Next page
41
8
Points droits
Largeur du point
AUTO
Abaissez le pied presseur.
Points droits
Tournez le volant vers vous jusqu'à ce que
l'aiguille soit dans la position la plus haute.
Relevez le pied presseur et mettez le tissu
sous le pied presseur.
Largeur du point
Pour coudre des points très serrés,
réglez la longueur du point sur un petit
nombre, par ex. sur «2». Pour obtenir
un point plus long, réglez sur un
nombre plus grand, par ex. sur «5».
Sélecteur de point
Tension du fil d'aiguille
Selector de tensión del hilo
Remarque : n'importe laquelle des trois positions d'aiguille
peut être sélectionnée pour la couture au point droit.
Position de l'aiguille
Selector de posición de la aguja
Puntada Recta
Nota: Cualquiera de las tres posiciones de la aguja puede
seleccionarse cuando se cose con puntada recta.
Selector de puntadas
Selector de ancho de puntada
Para una puntada muy cerrada, ajuste el
selector de Largo de Puntada a un número
más pequeño como «2». Para una puntada
más larga, ajuste a un número más alto,
como «5».
Gire el volante hacia usted hasta que la aguja
esté en la posición más alta.
Baje la palanca del prensatelas
Needle position
Note: Any of the three needle positions can be selected when
sewing a straight stitch.
Stitch width
For a very close stitch, set the Stitch
Length dial at a smaller number, such
as “2”. For a longer stitch, set at a
higher number, such as “5”.
Pattern selector dial
Turn handwheel counter clockwise until the
needle is in the highest position.
Raise presser foot lifter and slide fabric under
the presser foot.
Lower the presser foot.
Straight Stitching
Longueur du
point
Selector de largo
de puntada
Stitch length dial
0
5
4
3
1
2
Start with the Needle thread
tension in Auto position.
7
Enfilage de la machine
Relevez le releveur de pied presseur.
Remonter le fil de canette
Retenez le fil d'aiguille de façon lâche avec la main
gauche. Tournez le volant vers vous de la main droite pour
abaisser l'aiguille et continuez jusqu'à ce que l'aiguille
soit dans la position la plus haute.
Tirez légèrement le fil d'aiguille et saisissez le
fil de canette qui apparaît dans la fente de la
plaque à aiguille. Ensuite, tirez les deux fils
vers l'arrière de la machine et laissez
dépasser des bouts de fil de 15 cm.
Levante la palanca del prensatelas.
Sostenga el hilo de la aguja holgado con la mano
izquierda. Gire el volante hacia usted con la mano
derecha, bajando primero la aguja y continuando
hasta que la aguja llegue a su posición más alta.
Jale ligeramente hacia arriba el hilo de la aguja
y tome el hilo de la bobina que aparece por la
ranura de la placa aguja. Entonces jale ambas
hebras hacia atrás de la máquina, dejando un
extremo de 6 centimetros.
Ensartando la Máquina
Sacando el hilo de la bobina
Raising the bobbin thread
Raise presser foot lifter.
Hold needle thread loosely with your left hand.
counter clockwise with your right hand, first lowering
the needle and continuing until the needle comes to its
highest position.
Turn handwheel
Lightly pull up the needle thread, and pick up
the bobbin thread which will appear through
the needle plate slot. Then pull both threads
to the back of the machine, leaving a 6” thread
tail.
Threading the machine
40
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer 4220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer 4220 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 9,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info