Manual Silvercrest SDBK 2400 D3 - IAN 270055 (page 55 of 62) (English, German, Dutch, French)

645206

Zoom out

Zoom in

1/62

8. Cleaning

DANGER!

~ Pull the mains plug out of the wall socket

before you clean the steam iron.

~ Allow the device to cool down before

cleaning.

CAUTION:

~ Do not use any astringent or abrasive

cleaning agents.

Cleaning the device

• For cleaning the device, use a soft,

moistened cloth.

• Dirt can be removed from the sole plate

18 using commercially available clean-

ing agents for chrome, silver or stainless

steel.

• Residues that have melted on can be re-

moved by heating the steam iron up to

the MAX setting and then ironing an

old cotton cloth.

Self-cleaning

CAUTION:

~ Do not put vinegar, limescale remover

or any other additives into the water

tank 16. Additives can damage the de-

vice.

If you use tap water, you should run the self-

cleaning cycle after every use. Otherwise use

the self-cleaning cycle at least twice per

month.

1. Fill the water tank 16.

2. Place the steam iron in the stand 12.

3. Connect the mains plug with the wall

socket.

4. Set the steam flow rate control 5 to

and set the temperature controller 19 to

MAX.

5. Wait until the temperature control lamp

14 goes out.

6. The switch 11 is in the bottom position

. Remove the steam iron from the

stand 12. The cable base 10 remains

on the steam iron.

7. While doing so, hold the device hori-

zontally over a heat-resistant household

dish.

8. Press the 20 SELF-CLEAN button and

hold it down. Limescale residues will

then be ejected with steam and hot wa-

ter from the steam holes in the sole plate

18. Hold the button down until no more

steam or water emerges.

9. Repeat steps 1 to 8 until no more resi-

dues are coming out.

10.Pull out the mains plug, allow the device

to cool down, and pour off any remain-

ing water.

9. Storage

DANGER!

~ Store the steam iron out of the reach of

children.

1. Set the temperature controller

MIN.

2. Place the iron on the stand 12 and set

the switch 11 to the middle position .

3. Allow the device to cool down.

4. Set the steam flow rate controller 5 to

5. Set the switch 11 to the upper position

6. Remove the iron from the stand 12 and

pour off any remaining water through

the filling opening of the water tank (un-

der the lid 2).

7. Place the iron on the stand 12 and set

the switch 11 to the middle position .

8. Figure E: coil up the power cable in

the base of the stand.

9. Store the iron and the stand 12 in an

upright position.

B&3(B'DPSIEJHOHLVHQB%ERRN6HLWH0LWWZRFK-XOL

Where cwn i get a spare part for my silvercrest steam iron? Submitted on 11-2-2017 at 08:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDBK 2400 D3 - IAN 270055 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest SDBK 2400 D3 - IAN 270055 Manual

Product: