752906

Silvercrest IAN 313492 SPM 2000 A1 Manual

24
Zoom out
Zoom in
Previous page
1/98
Next page
24 GB/IE
ingredients which are
impeding
the mixing paddle
5.
If maintenance is required, please
contact the service point.
Before each use, please check
the mains cable 3, the plug, the
mixing chamber 1, the mixing
paddle 5 and the other remov-
able parts for damage. If you
find damage, please contact the
service address for a replacement.
To
prevent hazards, ensure that
all elements
have been fixed in
the correct place before you con-
nect the product to the power
supply.
Do not use the microwave or
other sources of heat to disinfect
the product. This could cause
deformation and defects.
Do not clean the product with
steel wool, scouring agents or
corrosive liquids.
Do not expose this device to
sunlight for prolonged periods.
This could cause decolouration.
Do not heat any parts of this
product.
Before first use
To prevent hazards, make sure that the device
is complete and the device, mains plug and
mains cable 3 are in good condition after
unpacking to rule out possible damage.
The device is packaged to protect it from trans-
port damage.
Carefully remove the device from the retail
packaging.
Remove all parts of the packaging and remove
the protective film from the display.
Thoroughly clean the device and all accessories
as specified in chapter „Cleaning and care“.
To do so, you will first have to disassemble the
device. Follow the instructions in the chapter
„Disassembling the product“.
After it has been thoroughly cleaned and re-as-
sembled (see chapter „Assembly“), set up the
pasta machine in the vicinity of a safety socket.
Make sure it is easily accessible.
Furniture nowadays is coated with a variety of
varnishes and plastics, and is
treated with the
most diverse of care products
. It is therefore im-
possible to rule out that some of these substances
may contain components which would attack
and soften the rubber feet of the housing 2. If
necessary, place an anti-slip pad under the
pasta machine.
Place the device on a suitable surface.
Connect the mains cable 3 with the socket on
the back of the device.
Connect the device to the safety socket.
Disassembling the product
Make sure that the device is switched off and
unplug the mains plug from the socket before
disassembling.
Remove the lid 4 from the housing 2 by op-
erating the release catch and then pulling the
lid 4 upwards using the handle.
Turn the shaping disk holder 9 anticlockwise
and remove it from the pressing tube 8.
Unscrew both fixing screws
15
by turning them
anticlockwise at the same time, until the front
panel 6 can be removed from the housing 2
without difficulty.
Pull the pressing tube including the auger 8
7 out of the mixing chamber 1.
… 24 …


Need help? Post your question in this forum.

Forumrules
1

Forum

silvercrest-ian-313492-spm-2000-a1

Reset search

  • Dzien dobry.
    Jak moge zakupic element 98200-993-004 do Silvercrest IAN 313492 SPM 2000 A1 w Polsce
    Pozdrawiam
    Waldemar Rostkowski
    Submitted on 16-4-2023 at 20:34

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest IAN 313492 SPM 2000 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest IAN 313492 SPM 2000 A1 in the language / languages: English, German, Dutch, French, Polish, Swedish as an attachment in your email.

The manual is 2,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info