Manual Silvercrest IAN 306041 SSR 3000 A1 (page 26 of 85) (English, German, Dutch, French, Polish, Swedish)

752909

Zoom out

Zoom in

1/85

26 GB/IE

Inserting / replacing batteries

Open the battery compartment cover on the

remote control.

Insert two batteries into the battery compartment

or replace the old batteries with new ones. Only

use batteries of the speciﬁed type (see „Technical

data“).

Note: When inserting the batteries, be sure to

observe the correct polarity. This is shown in

the battery compartment.

Close the battery compartment cover on the

remote control.

Operation

Due to the complexity of domestic environments the

product may skip some areas when cleaning. For

better cleaning results we recommend using the

product daily.

Preparation

Remove any obstacles prior to use, for example

power cables, toys and other objects.

Tuck rug edges under the rug. Do not allow

curtains and tablecloths to touch the ﬂoor.

Try to position furniture properly.

Test the product in areas with stairs. This allows

you to check whether the product can detect

the edge of area which it could fall oﬀ.

Do not stand in the way of the product when it

is working. Otherwise the product will be una-

ble to clean these areas.

Cleaning

Press the Clean button on the robot vacuum

cleaner 11 or on the remote control 27 if the

display shows „88:88“. The notiﬁcation will

switch to AUTO and the product will begin the

cleaning programme. If the product is in Standby

mode, the initial „88:88“ notiﬁcation will ap-

pear after the Clean button is pressed for the

ﬁrst time. When the Clean button is pressed for

a second time, the notiﬁcation switches to

AUTO and the cleaning programme begins.

Note: During automatic cleaning, the product

will switch to Corner mode when necessary, if

it is nearing a corner. After cleaning the corner,

the product will switch back to Normal mode.

To pause the cleaning programme part way

through, press the Clean button on the robot

vacuum cleaner 11 or on the remote control 27 .

To continue the cleaning programme, press the

Clean button on the robot vacuum cleaner 11 or

on the remote control 27 again within 15 sec-

onds. If the pause lasts longer than 15 seconds,

the product will switch to Sleep mode and the

notiﬁcation in the display 1 will go oﬀ.

You can also switch the product to Sleep mode

manually. To do so, hold the Clean button on

the robot vacuum cleaner 11 down for a few

seconds until the notiﬁcation in the display 1

goes oﬀ.

With the product paused, you can use the

directional buttons 26 on the remote control to

manually move it left / right / forwards / back-

wards.

Cleaning modes

For better cleaning results, the product has various

cleaning Modi. You can select the modes by pressing

the buttons on the product or on the remote control.

Spot mode

This mode is suitable for very dirty or very dusty

areas. In Spot mode, the product will focus on one

area to clean.

During cleaning, press the Spot mode button

on the robot vacuum cleaner 14 or the remote

control 29 to start this mode.

As soon as the surface is suﬃciently clean, the

product continues with the automatic cleaning

programme.

Note: You can also end Spot mode by pressing

the Clean button once on the robot vacuum

cleaner 11 or on the remote control 27 .

jeg har fejl e 12 hvad er det,har ikke manual mere Submitted on 6-6-2021 at 17:50
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest IAN 306041 SSR 3000 A1 in the language / languages: English, German, Dutch, French, Polish, Swedish as an attachment in your email.

The manual is 3,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest IAN 306041 SSR 3000 A1 Manual

Product: