790195
49
Zoom out
Zoom in
Previous page
1/56
Next page
Faults and what to do about them en
49
The spin cycle runs sev-
eral times.
Not a fault – the unbalanced load detection system is adjusting an imbalance.
The programme is taking
longer than usual.
Not a fault – the unbalanced load detection system is adjusting an imbal-
ance by repeatedly distributing the laundry.
Not a fault – the foam detection system is activated – a rinse cycle has
been switched on.
The length of the pro-
gramme changes during
the wash/dry cycle.
Not a fault – the programme sequence is optimised for the specific washing/
drying process. This may change the length of the programme shown on the
display panel.
Odours, stain formation in
the appliance.
Run the Cottons 90°C programme without laundry.
Add washing powder or a detergent containing bleach.
Note: To prevent foaming, only use half the amount of detergent recommend-
ed by the detergent manufacturer. Do not use detergents designed for woollens
or delicates.
Loud noises, vibrations
and appliance "move-
ment" during the spin
cycle.
Is the appliance aligned? ~ "Alignment" on page 19
Are the appliance's feet fixed? Secure the appliance's feet.
Have the transport locks been removed? ~ "Removing the transport
locks" on page 14
The display panel indica-
tor lights do not work
while the appliance is run-
ning.
Has there been a power failure?
Have the fuses blown? Reset/replace the fuses.
If the fault occurs repeatedly, call customer services.
There is detergent resi-
due on the laundry.
Some phosphate-free detergents contain water-insoluble residue.
Select Rinse or brush the laundry after washing.
Spin during the drying
phase.
This is an innovative process known as thermal spinning used to reduce energy
consumption during the drying phase. It is designed like this, please wait until
program finished.
Fluff found on the laundry. Run the Cottons Ž (cold) programme without laundry and detergent to
remove fluff which have accumulated inside the drum during the previous dry-
ing cycle.
Water inlet noise during
the drying phase.
The washer dryer uses water condensation technology, water is constantly
needed to dry the laundry. Therefore the water tap must be on all the time, till
the end of the drying phase.
Drying duration extended. Run the Cottons Ž (cold) programme to remove fluff which has collected
in the washer drum during the drying phase.
If the ambient temperature is higher than 30 °C, this may extend the drying
time.
Insufficient air circulation in the room may increase the drying time. Venti-
late the room.
Drying programme does
not start.
Drying additional programme setting not selected?
Door not closed properly?
Faults Cause/Remedy
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens WN44G290GB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens WN44G290GB in the language / languages: English as an attachment in your email.

The manual is 2.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info