652242

Siemens DH40018M Manual

11
Zoom out
Zoom in
Previous page
1/76
Next page
11
en
Operating instructions
Please read and observe the detailed safety instructions
at the start of these instructions!
■ Important: The appliance may never be exposed to frost!
Risk of electric shock!
Switch off the mains voltage supply immediately if
a fault occurs.
■ Immediately shut off the cold water supply to the appli-
ance should it leak.
Getting to know your appliance
The continuous-flow heater heats the water as it flows
through the appliance. The appliance only consumes power
during this period.
D
Operating elements
The continuous-flow heater has two heat settings:
e Economy setting – two thirds power
II Intensive setting – full power
The e setting is ideal for:
Wash basin
Shower
Bidet
The II setting is used in combination with a thermostatically-
controlled premixer, for high temperatures or for large vol-
umes of water, e. g. for:
Dishwashing
Cleaning
Bath tub
Operating the appliance
E
Turn on the hot-water tap
The continuous-flow heater switches on and heats the water
when the hot-water tap is turned on (Fig. E, 1.).
It switches off again when the tap is turned off.
Notes (not applicable for DH12...): When the water tap is
turned on only slightly, the continuous-flow heater will oper-
ate at half power in both of the preselected settings (e, II).
When the water tap is turned on fully, the appliance will oper-
ate at full, preselected power.
E
Increasing the water temperature
Slightly close the hot-water tap (Fig. E, 2.).
E
Decreasing the water temperature
Turn on the cold-water tap (Fig. E, 3.).
Startup after a water cutoff
■ Disconnect the appliance from the mains supply (remove
the fuses in the fusebox).
■ Turn on the hot-water tap until the air is purged from the
pipe.
■ Reinstall the fuses.
The appliance is ready for operation.
Saving energy
Use the “e” setting whenever possible.
For wash basins: Open the corner valve to such an extent
that only the lower heat setting switches on.
Winter operation
Note: It is possible in winter that the supply temperature of
the water is reduced and the required outlet temperature is
no longer achieved.
■ In order to compensate for this temperature reduction,
please reduce the water quantity on the tap until the re-
quired water temperature is achieved.
Cleaning
Simply wipe the appliance with a damp cloth.
Do not use acidic or abrasive cleaning materials.
Notes: It is normally not necessary to descale the appliance.
However, extremely hard water and the frequent flows of
very hot water can cause the appliance to scale up. In this
case please contact our after-sales service.
After-sales service
If you call the after-sales service for assistance, please specify
the E no. and FD no. of your appliance.
These numbers are found on the inside of the swing-out con-
trol panel of the continuous-flow heater.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens DH40018M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens DH40018M in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info