693647

Siemens Climatix 2 Manual

38
Zoom out
Zoom in
Previous page
1/77
Next page
INSTRUCTION MANUAL OF THE SIEMENS CLIMATIX 2 CONTROL EQUIPMENT
-
38
-
Radiators according to
DIN 4703
1.3
Heating convectors 1.25 – 1.45
The parameter setting is ranging from 1 – 2; the default value is 1.3.
The instructions for changing this parameter can be found in chapter 4.
After entering the service password (see chap. 5.24) it is possible to set:
The Minimum required temperature B1 parameter defines the minimal value of the required
temperature of the heated water at the HC1 inlet.
The parameter setting is ranging from 20 – 40°C; the default value is 20°C.
The instructions for changing this parameter can be found in chapter 4.
The Maximum required temperature B1 parameter defines the maximal value of the required
temperature of the heated water at the HC1 inlet.
The parameter setting is ranging from 40 – 85°C; the default value is 80°C.
The instructions for changing this parameter can be found in chapter 4.
The Boost source parameter sets an increase in the required temperature of the heated water of
a source (boiler) compared to the instantaneous value of the required temperature of the heated
water at the HC1 inlet.
The parameter setting is ranging from 0 – 20 °C; the default value is 5 °C.
The instructions for changing this parameter can be found in chapter 4.
6.4.6. PUMP HC1
After clicking on the line Pump HC1 it is possible to enter the menu where all parameters
concerning the pump HC1 can be set:
The Frost protection parameter activates or deactivates the operation of the pump HC1 at low
temperatures.
The instructions for changing this parameter can be found in chapter 4.
The HC1 overrun time parameter defines the delay of switching off the pump HC1 when the
demands on heating the heating circuit 1 are met.
The parameter setting is ranging from 0 – 1200s; the default value is 120s.
The instructions for changing this parameter can be found in chapter 4.
6.4.7. ROOM THERMOSTAT H1 HC1
After clicking on the line Room thermostat H1 HC1 it is possible to enter the menu where the
polarity (the operating logic) of external contact H1 can be set. The default value is Operating; i.e.
if the contact of the room thermostat is closed, the heating is switched to the “frost protection”
mode.
… 38 …


Need help? Post your question in this forum.

Forumrules
1

Forum

siemens-climatix-2

Reset search

  • salve
    chiedo se è possibile fare un by pass per far partire il sistema di condizionamento a causa dell'oscuramento :del controllore POL/STD
    grazie
    Submitted on 11-3-2022 at 12:44

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens Climatix 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens Climatix 2 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info