759461

Sencor SRV 9250 Manual

9
Zoom out
Zoom in
Previous page
1/11
Next page
- 9 - 07/2019
Copyright © 2019, Fast ČR, a.s.
INSERTING AND REPLACING BATTERIES IN THE REMOTE CONTROL
■ Push down the latch of cover C13 on the rear side of the remote control C1 to
release it and remove the cover.
■ Insert two type AAA (1.5 V) batteries into the remote control. When inserting the
batteries, ensure the correct polarity as shown inside the battery compartment C14.
Put the cover C13 back on and click it into place.
■ In the event that the batteries are flat, replace them with new ones. Do not combine
various types of batteries or new and old batteries.
■ The signal range of the remote control is approximately 6 m.
SETTING THE SYSTEM TIME OF THE ROBOTIC VACUUM CLEANER
■ The system time of the vacuum cleaner is the actual time according to your time
zone. It must be correctly set if you wish to use the scheduled cleaning function.
■ In the stand-by mode or in the charging in the charging station mode, hold down
button C11 (CLK) until the time setting value (hours and minutes) starts flashing
on the display C2.
■ Using buttons C5 ( ) or C8 ( ) set the time values. Toggle between the hour and
minute numbers using buttons E6 ( ) or C7 ( ).
■ Confirm the set time by pressing button C11 (CLK). 1× beep will be made and the set
time will be saved to memory as the system time.
■ If you do not perform any changes within 10 seconds, the system time setting mode
will automatically be cancelled and the time will not be saved to memory.
DEFINING THE VACUUMING AREA USING MAGNETIC TAPE
■ The magnetic tape I1 serves to define the vacuuming area without you having
to close doors or place artificial obstacles in the path of the vacuum cleaner. The
vacuum cleaner will recognise the magnetic tape and will not travel over it. It will
start cleaning in another direction.
■ Place the magnetic tape before the place that the robotic vacuum cleaner should
not clean, for example room doorway, carpet, cables on the floor or astaircase with
rounded corners, etc.
■ To help the magnetic tape adhere better, you can attach it to the perimeter using
standard double-sided tape. It can also be cut into smaller pieces as required.
Additional tape can be purchased to extended the defined area.
Note:
The magnetic tape must be put down prior to every cleaning session
because the robotic vacuum cleaner does not store the boundaries in
memory.
OPERATING THE ROBOTIC VACUUM CLEANER
Note:
Before starting the vacuum cleaner, always make sure that either
the dust container A6 or the complete mop unit A7 including the
respective HEPA dust filters is inserted inside.
TURNING ON THE ROBOTIC VACUUM CLEANER
■ Turn on the power supply to the vacuum cleaner using the main switch A4.
■ Press button D1. The button'sindicator will start flashing blue. When the indicator
is permanently lit blue, the vacuum cleaner is in stand-by mode and ready for
operation.
STAND-BY MODE
■ The stand-by mode means that the vacuum cleaner is ready for operation. Button
D1 is backlit in blue colour.
■ Set the vacuum cleaner to the stand-by mode by pressing button D1 on the vacuum
cleaner or buttons C9 (ON/OFF) on the remote control either by turning on the
power supply using main switch or whenever while the vacuum cleaner is running.
SLEEP MODE
■ The sleep mode serves to save the battery'scapacity. The vacuum cleaner enters
sleep mode either automatically after ten minutes of inactivity or when it is unable
to dock in the charging station. The backlight on button D1 will turn off and the
vacuum cleaner will automatically switch to the sleep mode.
■ To wake the vacuum cleaner from the sleep mode to the stand-by mode, press
button D1 on the vacuum cleaner or the control button C9 (ON/OFF) on the remote
control.
Note:
When the vacuum cleaner is in sleep mode, it is not possible to wake it
up using the mobile phone application. In sleep mode, it reacts only to
buttons D1 or C9 (ON/OFF) on the remote control.
TURNING VOICE MESSAGES ON/OFF
■ If you prefer not to have the vacuum cleaner make system voice messages,
deactivate this function by simultaneously pressing buttons C3 (PLAN) and C4
(HOME) on the remote control. The vacuum cleaner will only make beeps.
■ If you wish to reactivate the voice messages, again simultaneously press the buttons
C3 (PLAN) and C4 (HOME).
TURNING OFF THE ROBOTIC VACUUM CLEANER
■ If you wish to completely turn off the vacuum cleaner, set the main switch A4 to
position 0 (off ). The backlight on button D1 will turn off and the power supply will
be shut off. When the vacuum cleaner is turned off, it will not respond to any button.
SELECTING THE ROBOTIC VACUUM CLEANER CLEANING MODE
■ Before starting the cleaning process, check that the entry door into your apartment
or house is closed. From the floor surfaces, remove clothing, paper, toys, power or
extension cords and other items that the vacuum cleaner could suck in or catch.
Lift curtains and drapes that reach to the floor so that the vacuum cleaner does not
catch them.
Tip:
When vacuuming in a new environment for the first time, carefully
observe the movement of the vacuum cleaner. You can thereby
recognise problematic obstacles and remove them for the next
cleaning session.
AUTOMATIC CLEANING MODE
■ Press button D1 or button C9 (ON/OFF) on the remote control. The vacuum cleaner
will enter the automatic cleaning mode, in which it effectively combines various
routes to achieve an optimal clean of the entire floor area. As soon as the vacuum
cleaner finishes cleaning, it will seek out the charging station and dock there to
recharge.
MAXIMUM POWER MODE
■ Press button C12 (MAX) on the remote control. The vacuum cleaner will enter the
cleaning mode, in which it effectively combines various routes to achieve an optimal
clean of the entire floor area. This mode is characterised by increased motor and
central rotary brush power for the purpose of achieving the most effective cleaning
process.
SILENT CLEANING MODE
■ Repeatedly press button C10 (MODE) on the remote control so that display C2
shows MODE1. The vacuum cleaner will enter the silent cleaning mode in which
the fan speed and suction power is reduced. Cleaning is performed as quietly as
possible without interrupting you during work or while you are relaxing. After
finishing cleaning, it will seek out the base station for recharging.
AUTOMATIC MOVEMENT MODE
■ Repeatedly press button C10 (MODE) on the remote control until MODE2 appears
on the display E2. The vacuum cleaner will enter the automatic movement mode in
zig-zag style. After finishing cleaning, it will seek out the base station for recharging.
INTENSIVE CLEANING MODE
■ Repeatedly press button C10 (MODE) on the remote control so that display E2
shows MODE3. The vacuum cleaner will enter a mode in which the fan speed and
suction power is increased. It will then end the cleaning process and seek out the
charging station in order to recharge itself.
PAUSING THE CLEANING PROCESS
■ Press button D1 or C9 (ON/OFF) on the remote control at any time during the
cleaning process to stop the vacuum cleaner in the place where it is cleaning.
USING THE MOP UNIT
■ The mop unit is used for simultaneous vacuuming and dry or wet wiping of smooth
floor surfaces. It consists of the removable dust container E1, water tank E2 and the
mop fabric E3. The water tank is equipped with an electronically-controlled water
pump that automatically doses the water on to the fabric and also stops dosing
water at the end of the cleaning process to prevent water from leaking on to the
floor or the charging station.
Attention:
Only use the mop unit intended for this type of robotic vacuum
cleaner.
Do not use the water tank E2 without the mop fabric attached.
The mop unit is not intended for cleaning carpets.
Dry wiping of floors
■ Dry wiping is used for removing fine dust and floor polishing.
■ If the mop unit is inserted inside the vacuum cleaner, press latch A8 and slide the
unit out of the vacuum cleaner.
■ Attach the mop fabric to the underside of the water tank using the velcro zip E4 on
the water tank and insert the unit back into the vacuum cleaner.
■ Start the vacuum cleaner.
Wet wiping of floors
■ Wet wiping is used for cleaning away minor dirt and floor polishing
■ If the mop unit is inserted inside the vacuum cleaner, press latch A8 and slide the
unit out of the vacuum cleaner.
■ Slide the dust container out of the water tank.
■ Attach the mop fabric to the underside of the water tank using the velcro zip E4
on the water tank.
■ Open the cap E5 and fill the tank with water. Properly insert the cap back in. Wipe
any excess water off the water tank. Take special care to ensure that the contacts
E6 are dry.
Note:
For wiping, we recommend using clean water. If you use a cleaning
agent, it may foam up and thereby worsen the dripping of the water
on to the fabric, or potentially cause smudges on the floor after it dries.
… 9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SRV 9250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SRV 9250 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info