759963
8
Zoom out
Zoom in
Previous page
1/12
Next page
EN-8
EN
Hair Clipper
SHP 3301BL / SHP 3302RD / SHP 4301BL / SHP 4302RD
2016 05/2016
C
Turn on the hair clipper by sliding switch A6 to the ON position.
Attention:
The cutting unit A1 will cut off all hair that comes into contact with it, therefore be especially
careful when handling the hair clipper while it is running.
Cutting without the comb attachment A2 is used primarily for trimming up sideburns and the ear
line and the nape of the neck. When trimming the ear line, hold the hair clipper so that the blade
of the cutting unit A1 points downwards ensuring that only the cutting blades are in contact with
the hair. When trimming the line at the nape of the neck, hold the hair clipper so that the blade
of the cutting unit A1 points downwards. Touch the skin with the cutting blade only very lightly.
When you have finished using the hair clipper, turn it off by moving switch A6 to the OFF position
and clean it out according to the instructions in the chapter ‘Cleaning and Maintenance’
2.2 TRIMMING A BEARD
Proceed in the same way as when cutting hair. Trim the beard when it is dry without the use of
shaving gels or foams.
Trim the beard by slowly moving against the growth direction of the beard, going from the bottom
upwards.
CLEANING AND MAINTENANCE
Before starting to clean the hair clipper, make sure that it is turned off and disconnected from the
power socket.
Regular cleaning after every use will ensure optimal performance of the hair clipper.
Attention:
This hair clipper is not designed to be washed under the water tap. Do not spray the hair clipper or
the power adapter A8 with water or any other liquid or submerge it in water or any another liquid.
CLEANING
Remove the comb attachment A2 from the cutting unit A1 if attached. Hold the hair clipper in your
hand so that your thumb is located on the cutting blade. Use your thumb to push the cutting blade
from the body of the hair clipper A3 until the cutting unit A1 is completely released. Take the cutting
unit A1 off the body of the hair clipper A3. Use the brush A9 to remove all hair or beard remains
from the cutting unit A1 and from the area of the body of the hair clipper A3 underneath the cutting
unit A1. After cleaning, reattach the cutting unit A1 to the body of the hair clipper A3. Position the
cut-out at the foot of cutting unit A1 against the notch on the body of the hair clipper A3 and then
push the cutting unit A1 onto the body of the hair clipper A3 until there is an audible click.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SHP 3301 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SHP 3301 in the language / languages: English as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info