759963
7
Zoom out
Zoom in
Previous page
1/12
Next page
Hair Clipper
SHP 3301BL / SHP 3302RD / SHP 4301BL / SHP 4302RD
EN
EN-7
2016 05/2016
B
Use the regulator A5 to set the desired hair cut height in the range from 1 to 8 mm. If you
are using the hair clipper for the first time, it is recommended to first try a longer cut and only
thereafter adjust the setting as required.
Turn on the hair clipper by sliding switch A6 to the ON position.
Attention:
The cutting unit A1 will cut off all hair that comes into contact with it, therefore be especially
careful when handling the hair clipper while it is running.
To ensure an even haircut, the flat part of the comb attachment A2 must constantly remain in
contact with the scalp. Slowly move the hair clipper against the direction of hair growth.
Regularly remove hair accumulating in the attachment A2. Prior to removing the hair, turn off the
hair clipper. Hold the attachment A2 by the sides and slide it off in the direction away from the
cutting unit A1. Remove the hair and then attach the attachment A2 back onto the cutting unit
A1. Set the cutting height again, turn on the hair clipper and continue with the haircut.
When you have finished using the hair clipper, turn it off by moving switch A6 to the OFF position
and clean it out according to the instructions in the chapter ‘Cleaning and Maintenance’.
1.2 TRIMMING A BEARD
Proceed in the same way as when cutting hair. Trim the beard when it is dry without the use of
shaving gels or foams.
Trim the beard by slowly moving against the growth direction of the beard, going from the bottom
upwards. Please remember that the comb attachment A2 must constantly remain in contact with
the skin to ensure an even cut. After reattaching the attachment A2 back onto the cutting unit
A1, do not forget to set the cutting height again.
2. TRIMMING WITHOUT THE COMB ATTACHMENT
2.1 CUTTING HAIR
Use the hair clipper on clean, dry or lightly dampened hair. Before cutting hair, thoroughly comb
out the hair in the direction of growth.
Seat the person whose hair you will be cutting in such a way that their head is at the height of your
chest. Use a towel to cover the neck and shoulders to protect clothing from hair clippings.
Hold the comb attachment A2 by the sides and slide it off in the direction away from the cutting
unit A1. When the hair clipper is used without the comb attachment A2, the cut will correspond
to a height of approximately 0.5 mm.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sencor SHP 3301 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SHP 3301 in the language / languages: English as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info