Manual Sencor SES 7015CH (page 7 of 8) (English)

758390

Zoom out

Zoom in

1/8

- 7 - 03/2020

ECO mode Fast mode Default

settings

Spout light A8 No Yes Yes

Pre-brew function* Yes No Yes

Automatic shut-o time 10 minutes 30 minutes 20 minutes

Option to save amount of

espresso / hot water to memory

Yes Yes Yes / Reset to

default settings

*Note:

The pre-brew function means that the ground coee is rst moistened with asmall

amount of water. This will cause the coee to swell and thereby when it is subsequently

fully brewed, its avour will be developed fully, and its aromatic compounds and essential

oils will be fully extracted.

1. In the stand-by mode, press and hold down button B7 for 5 seconds. Button B7

will start ashing and at the same time other buttons will also be ashing or lit

depending on the mode that is set.

Button B8 Button B9 Button B10

ECO mode Lit Flashing Flashing

Fast mode Flashing Lit Flashing

Default settings Flashing Flashing Lit

2. To set the ECO mode, press button B8, to set the fast mode press button B9 and

to reset to default settings, press button B10. After setting amode, 2 beeps will

be made. In the event that you attempt to set amode that is already set, the

appliance will not react to the button being pressed.

3. If you do not wish to change the mode settings, press button B7 once more, or

wait 5 seconds until the appliance automatically switches back to the stand-by

mode.

CLEANING AND MAINTENANCE

Everyday cleaning and maintenance

■

Timely cleaning and maintenance is very important for operating the appliance

and extending its lifetime.

■ Before cleaning, turn off the appliance, disconnect it from the power socket and

allow it to cool down.

■ Remove the outer drip tray A11. Empty out all its contents over asink, and wash it

using clean water and then dry it thoroughly.

■ Slide out the inner drip tray A10 with the coffee grounds container A9. Empty out

the coffee grounds container A9 and wash it with clean water. Then dry it thoroughly.

Empty out the inner drip tray A10 and if dirty, wipe it with aclean dampened cloth

and then dry it thoroughly.

■ Install the inner drip tray A10, coffee grounds container A9 and the outer drip tray

A11 back in their place.

■ Slide out and remove the service access door A7. Press the brewing unit release

button and take out the brewing unit A6. Wash it under running water and dry

it out thoroughly.

■

Install the brewing unit A6 properly in its place and attach the service access door A7.

■ In the event that the appliance will not be used again on the same day, empty out

the contents of the water tank A1 and put it back in its place.

■

Once amonth, it is recommended to thoroughly clean out the water tank A1 using

asoft cloth and asolution of water and neutral kitchen detergent. Then thoroughly

rinse out the water tank A1 with clean water, dry it and put it back in its place.

■ Only clean the coffee bean hopper A3 with aclean, dry cloth or paper towel. Do

not clean it with water.

■ To clean the outer surface of the appliance, use aclean, lightly dampened cloth.

Then wipe everything so that it is thoroughly dry. Do not use solvents, steel wool,

abrasive cleaning agents, etc. to clean the appliance.

■

Do not submerge the appliance or its power cord in water and do not wash it

under running water.

Self-Clean function

■

When indicator B5 lights up during operation, it is necessary to start the Self-

Clean function.

■

The appliance will work best when the Self-Clean function is used regularly, at least

once per month, or more frequently based on the hardness of the water that is

used. This will extend its lifetime and improve power efficiency because limescale

deposits negatively affect electricity consumption.

■

Fill the water tank A1 all the way to the maximum water mark according to the

instructions contained in chapter Filling the water tank.

■

Add descaling agents specially intended for descaling espresso machine type

appliances into the water tank A1. These agents can normally be purchased in

specialised electrical appliance stores or in online stores. Follow the instructions

on the manufacturer’spackaging when dosing the purchased descaling agent.

Attention:

For descaling, do not use vinegar, etc. Otherwise, the appliance could be

damaged.

■ Under the spout A8, place acontainer with acapacity of at least 1.1l.

■

In the stand-by mode, simultaneously press and hold down buttons B7 and B9

for 5 seconds. Abeep is made and indicator B5 and touch button B9 will flash.

■ To start the self cleaning process, press button B9.

Note:

In the event that you wish to return to the stand-by mode at this stage, press button B7.

■ The progress of the self cleaning procedure is signalled by indicator B5. Take care

to prevent scalding by hot water or the escaping steam. Do not interrupt the

process in this phase.

■

Once the water in the water tank A1 is used up, indicator B1 and button B9 will start

flashing. Empty out the remaining contents of the water tank A1 and fill it up to the

maximum water mark with clean water. When the filled water tank A1 is inserted

back into the appliance, indicator B1 will turn off.

■ Empty out the contents of the container under the spout A8 and put it back in its

place. To complete the self cleaning process, press button B9.

■

When the self cleaning process is complete, the appliance will turn off automatically.

Manual cleaning (ushing the spout)

■

We recommend that you always clean the coffee spout when you have finished

using it. It is also recommended to do this when the appliance has not been used

for an extended period of time.

■

In the stand-by mode, simultaneously press and hold down buttons B7 and B8

for 5 seconds.

■

The light on buttons B8, B9 andB10 will turn off. Asmall amount of water will

flow out of the spout, which will flush it out. Water will flow into the drip tray A11.

Attention:

Avoid coming into contact with hot water.

■

After finishing the manual clean, the appliance will switch back to the stand-by

mode.

Drain internal lines

■

It is recommended to drain the internal lines when you plan on not using the

appliance for and extended period of time, before transporting it, etc.

■ In the stand-by mode, simultaneously press and hold down buttons B7 and B10

for 5 seconds. Indicator B6 will start flashing.

■ Remove the water tank A1 from the appliance. Indicator B6 will be lit. This signals

that the draining of the internal lines is running.

Note:

If you press button B7 before taking out the water tank A1, you will return back to

the stand-by mode.

■

When the internal line draining process is complete, the appliance will turn off

automatically.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sencor SES 7015CH in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sencor SES 7015CH Manual

Product: