Manual Scubapro MERIDIAN (page 39 of 58) (English)

550298

Zoom out

Zoom in

1/58

3. Meridian as a dive computer

English

SCUBAPRO MERIDIAN

something did not work as planned.

WARNING

• Diving with two gas mixtures represents a

much higher risk than diving with a single

gas mixture, and mistakes by the diver may

lead to serious injury or death.

• During dives with two gas mixtures, always

make sure you are breathing from the tank

that you intend to breathe from. Breathing

from a high oxygen concentration mix at the

wrong depth can kill you.

• Mark all your regulators and tanks so

that you cannot confuse them under any

circumstance.

• Before each dive and after changing a tank,

ensure that each gas mixture is set to the

correct value for the corresponding tank.

• Get a proper training and certiﬁcations to

make multi-gas dives prior of making them.

Meridian enables you to use up to two gas

mixtures during the dive (air and Nitrox

only). The two mixtures are labeled 1 and

d, and must be in ascending order of the

oxygen fraction.

1 d

Time

Bottom mix

Diving with 2 gas mixtures

Deco mix

Depth

Switching gas mixture during the dive

During the ascent phase, when you reach a

depth corresponding to the MOD of Gas d,

Meridian will suggest that you perform the

switch. An audible sequence goes off,

and the text Gas d starts ﬂashing on the

display together with the value of the MOD.

You have 30 seconds to respond to this

message, otherwise Meridian will consider

that Gas d will not be used and adapts the

decompression schedule accordingly. To

conﬁrm the gas switch, press SEL/ESC

button.

NOTE: Start breathing from the tank

with the new gas mixture before

conﬁrming a switch.

WARNING

Always make sure you are switching to the

intended gas. Failure to do so may result in

serious injury or death.

After you conﬁrm the switch, the text

Gas d remains on the screen for ﬁve

seconds without ﬂashing.

Switching back to a gas mixture with

lower oxygen concentration

There may be situations in which you have

to switch back to Gas 1 from Gas d. This

can happen for instance if you want to

descend again below the MOD for Gas d,

or if for instance you have run out of Gas

d during the decompression. At this point

you can manually initiate the gas switch by

pressing and holding SEL/ESC button.

Meridian will display the text Gas 1 and

its MOD, ﬂashing. At this point press

SEL/ESC button to conﬁrm the switch.

Meridian will display the text Gas 1 for ﬁve

seconds without ﬂashing and adapt the

decompression schedule accordingly.

Gas switch not carried out at the

planned depth

If you fail to conﬁrm the change to Gas d

within the 30 seconds of when Meridian

suggested it, Gas d is excluded from

the decompression calculation and the

decompression schedule is adapted

Hi. What is error message E37 on the Meridian. Just did a dive and computer would not go into dive mode. When I came out it said E 37 Submitted on 27-4-2024 at 12:45
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scubapro MERIDIAN in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scubapro MERIDIAN

Scubapro MERIDIAN User Manual - German - 58 pages

Scubapro MERIDIAN User Manual - Dutch - 58 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scubapro MERIDIAN Manual

Product: