781864

Scheppach Wox D 700SL Manual

23
Zoom out
Zoom in
Previous page
1/48
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58 www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
23GB
When connecting to the mains or in the event of the
machine being moved to another location, the turn-
ing direction must be checked. It may be necessary
to change the polarity.
Turn pole inverter in the machine socket.
Motor-brake appliance
The brake slowes down the motor of the saw shaft
within 10 seconds.
The electrical braking is interrupted after maximum
14 seconds.
In case the braking takes more than 10 seconds the
machine should not be used again, as the brake is
defective. The machine implicitly needs to be discon-
nected from the power supply. Only an electronic spe-
cialist should be instructed to repair this malfunction.
Operating mode / Switch-on duration
The electrical motor is dimensioned for operating
mode S6 - 40 %.
S6 = pass operation with load exposure
40% = related to 10 min. 4min. load; 6min. pass oper-
ation
If the motor is overloaded, it automatically switches
off because a thermostat protects the motor against
overloading. After a cool-down period (time varies)
the motor can be switched on again.
Check electrical connection
• Switch on the machine with the power switch, the
motor runs up.
Attention!
Check the direction of rotation!
• Three-phase AC motors must be checked for their
direction of rotation in the event of a new connec-
tion or change of location. If necessary, the direc-
tion of rotation must be changed with the phase
inverter (Fig. A)
• Upon switching off the saw shaft is slowed down
within 10 seconds.
Changing of rolling direction
Fig. A
m Connections and repairs of the electrical equip-
ment should only be carried out by an electrical spe-
cialist.
In case you have further questions, please specify
the following:
• Motor manufacturer; Current type of the motor
• Type of current for the motor
• Information of the machine type label
• Information of the switch type label
If you send the motor back, always return the
complete power unit with electro-control. m
12. Commissioning
• Before commissioning observe the safety notes.
• All safety and auxiliary installations must be tted.
• Check the rocker, which must return to the initial
position independently. Check the saw blade for
perfect t and the correct direction of rotation.
• Functional check before start of work.
• To operate the saw, press the on / off switch.
• The saw is constructed solely for the cross cutting
of rewood with max. 1 meter length.
• Regardless of the wood diameter, put only one
piece with min. Ø 60 mm on the rocker.
• Use both hands to swing the rocker to the saw
blade.
• Then place the rocker in the initial position.
• The wood to be sawn must not be xed by hand.
• After the complete standstill of the saw, pull the
mains plug or the ignition plug.
• Only carry out conversion, adjustment, measure-
ment and cleaning work with the engine switched
off. Wait until the rotating tool has come to a stand-
still and remove the mains plug.
12.1 Commissioning Wox d 700
The Wox d 700 provides maximum safety thanks to
its enclosed sawing area.
Cut off the cable ties on the tension springs. Open the
protective cover (1) and mount the tension springs as
displayed in the image.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Wox D 700SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Wox D 700SL in the language / languages: English, German, French as an attachment in your email.

The manual is 3.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info