Manual Scheppach Structo 5 (page 11 of 54) (English, German, French, Italian, Polish, Finnish)

782182

Zoom out

Zoom in

1/54

12 english

If necessary, correct as follows (Fig. 8.1):

Release the 4 hexagon bolts (2).1

Adjust the riving knife.2

Retighten the hexagon bolts (2).3

The riving knife is an important protective device for •

guiding the work piece and closing the gap behind

the sawblade, thus avoiding the kick-back of the work

piece. Mind the thickness of the riving knife – see the

embossed ﬁgures on the riving knife. The riving knife

must not be thinner than the sawblade and not thicker

than the width of the cutting gap.

Fig. 9

The riving knife must be in line with the sawblade. Correct

any difference as follows:

Release two hexagon bolts (1) each on both sides.1

Align the riving knife vertically.2

Slightly tighten the hexagon bolts (1).3

Adjust the riving knife in line with the sawblade, and 4

retighten the four hexagon bolts.

Check the clearance to the sawblade.5

Note:

If, at switching off, the brake lacks efﬁciency, it must be

examined by a specialist or replaced. A defective push

stick must be replaced.

 Electrical connection

The installed electrical motor is connected ready to oper-

ate. The connection complies with the relevant VDE- and

DIN-regulations.

The power supply as well as the used extension cable

should comply with these regulations.

Motor-brake facility

Your construction circular saw is equipped with an auto-

matically functioning deadlock brake. The brake starts

functioning after switching off the motor.

Important information

The electrical motor is made for operating mode S 6 /

40 % .

When the motor gets overcharged, it automatically switch-

es off. After a short cool-down period (time varies) the

motor can be switched on again.

Defective electrical power supply cords

Electrical power supply cords often suffer insolation dam-

ages. Causes are:

Pressure spots, when power supply cords are being led •

through windows or doors.

Buckling spots by incorrect attachment or guidance of •

the power supply cords.

Cuttings by driving over a power supply cord. •

Insulation damages through pulling out of the socket. •

Cracks in worn-out insulation. •

Such defective electrical power supply cords should not

be used and are extremely dangerous because of the in-

sulation damage.

Check electrical power supply cords for damages on a reg-

ular basis. Please observe that upon checking the power

supply cord is not plugged in. Electrical power supply

cords have to comply with the relevant VDE - and DIN-

regulations. Only use power cables with the qualiﬁcation

H 07 RN. An imprint of the type denomination is rule.

Alternating current motor, Page U5

The supply voltage should be 230 Volt/50 Hz.•

Extension cables must be up to 25 m long, have a cross •

cut of 1.5 square millimeter, be over 25 m long, and

have a minimum 2.5 square millimeter.

The powersupply should be 16 A.•

Rotary current motor

The power supply should be 400 Volt/50 Hz.•

The power supply and the extension cables must be •

5-fold leads = 3 P + N + SL.

Extension cables must have a minimum cable cross •

section of 1.5 square millimeter.

The power supply should be maximum 16 A.•

In case of connection to the power supply or moving •

site the rotary direction should be checked, otherwise

the polarity has to be changed (wall mounted connec-

tor).

Therefore screw the phase switcher into the plug sur-•

rounding with a screw driver. (See Fig. 10)

Connections and repairs of the electrical equipment should

only be carried out by an electrical specialist.

In case you have further questions, please specify the

following:

Motor manufacturer•

Current type of the motor•

Information of the machine type label•

Information of the switch type label•

When sending back the motor, always return the complete

power unit with switch.

Implementation

Please read the safety information before implementa-

tion.

The implementation of the machine is only admissable

when protection and safety facilites have been installed

completely.

Put the machine on a stable, even ﬂoor. If necessary at-

tach through the bottom through the holes to the frame

valves. (screws/nails)

After connection to the power supply your scheppach con-

struction circular saw is ready to operate.

Longitudinal cuts, Fig. 11

Use the fence for parallel cuts.•

For working smaller work pieces (less than 120 mm) •

use the push stick and the low fence side.

Attention: Do not use a defective or broken push stick •

or push handle any more (risk of injury).

A defective push stick and push handle must be •

replaced by new ones.

Immediately dispose of any defective parts.•

Cross cuts, Fig. 11.1

Use the cross-cutting gauge for cross and angle cuts.•

It is ready for use by lifting it onto the saw table.•

The setting scale reaches from 0° to 90°.•

In order to achieve a precise cut, press the wood against •

the fence surface when sawing.

When not used, lower the cross-cutting gauge at the •

side.

Wedge-cutting gauge, Fig. 11.2

The cross-cutting gauge is also used for cutting •

wedges.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Structo 5 in the language / languages: English, German, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 9.22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Structo 5 Manual

Product: