Manual Scheppach Structo 5 (page 12 of 54) (English, German, French, Italian, Polish, Finnish)

782182

Zoom out

Zoom in

1/54

english 13

To this purpose, set the swinging part to 0° and ﬁx it •

with the adjustment handle.

Place the wood into the recess and saw it carefully •

exerting a uniform pressure.

Switch off the machine and remove the wedges.•

Caution: Feed the work piece only with your hand on •

the cross-cutting gauge. Do not hold the work piece

by hand.

Changing the sawblade, Fig. 12.1 and 12.2

Attention: Pull the power plug!

Screw out the two upper bolts M 8 (1) from the lower •

sawblade guard.

Swing down the sawblade guard. Release the tension •

nut (M 20, left-hand thread) and ﬁx it with the holding

key (Fig. 12.2).

Wear gloves to protect your hands. •

Remove the sawblade and ﬁt a now one. •

Only mount a well sharpened, crack-free and not •

deformed sawblade.

Tighten the tension nut, ﬁxing it with the holding key •

(left-hand thread!).

Raise the lower sawblade guard, re-insert the two bolts •

M 8 and tighten them.

After every sawblade change, the riving knife must be •

adjusted anew - see Setting the riving knife Fig. 2.

Maintenance

Switch the motor off and pull the power plug before doing

any maintenance and cleaning work.

After servicing the machine, all guards and safety devices

must be reﬁtted.

The construction saw, including the electric motor, •

are maintenance-free to a far extent. An exception are

the sawblades, table inserts and brake linings of the

electric motor (approx. 14,200 switching actions) that

are subject to natural wear and tear.

The sawblade must stop within approx. ten seconds. If •

necessary, the worn table insert must be replaced.

Brake linings may only be replaced by specialists.•

Cleaning

Attention: Pull the power plug!

Wear gloves (risk of cutting).

Always wear goggles for cleaning to protect your eyes. •

Remove dust and dirt at regular intervals.•

Keep the protective sawblade box clean from scrap •

wood and saw dust cloggings.

For a good cleaning compressed air or a hand broom •

are recommended.

Keep the table surface free from resin.•

Caution: Do not use any cleaning agents on the plastic •

parts. We recommend a mild rinsing agent on a moist

cloth.

EC Declaration of Conformity

We herewith declare, scheppach Fabrikation von

Holzbearbeitungsmaschinen GmbH, Günzburger Str. 69, D-89335

Ichenhausen that the machine described below due to its con-

struc tion and design and in the version delivered by us complies

with the relevant provisions of the following EC Directives.

In case of a modiﬁcation of the machine this declara tion ceases

to be valid.

Machine description:

Circular construction saw

Machine type:

structo 5

Relevant EC directives:

EC machine directive 98/37/EG (< 28.12.2009),

EC machine directive 2006/42/EG (> 29.12.2009),

EC Low voltage directive 2006/95/EWG,

EC-EMV directive 2004/108/EWG.

Applied harmonized European Standards

EN 12100-1, EN 12100-2, EN 294, EN 349, EN 418, EN 847-1,

EN 954-1, EN 1088, EN 1870-1, EN 60204-1, EN 55014, EN 60555-

2, EN 60555-3

Notiﬁed Body

ISO 7960

The machine corresponds to the checked template according to

Appendix VII:

Fachausschuß Holz; 70504 Stuttgart

Prüf- und Zertiﬁzierungsstelle im BG-PRÜFZERT

Called in for:

EC type-examination

GS-Prüfbescheinigung

Place, date:

Ichenhausen, 15.10.2009

Signature:

Wolfgang Windrich (product manager)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Structo 5 in the language / languages: English, German, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 9.22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Structo 5 Manual

Product: